AD8803ARZ Analog Devices Inc, AD8803ARZ Datasheet - Page 9

• Manufacturer Part Number: AD8803ARZ
• Description: IC DAC 8BIT OCTAL W/SD 16-SOIC
• Manufacturer: Analog Devices Inc
• Series: TrimDAC®r

Specifications of AD8803ARZ

• Data Interface: Serial
• Settling Time: 600ns
• Number Of Bits: 8
• Number Of Converters: 8
• Voltage Supply Source: Single Supply
• Power Dissipation (max): 27.5mW
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (3.9mm Width)
• Resolution (bits): 8bit
• Sampling Rate: 1.7MSPS
• Input Channel Type: Serial
• Supply Voltage Range - Analog: 2.7V To 5.5V
• Supply Current: 1mA
• Digital Ic Case Style: SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

REV. A
Increasing Output Voltage Swing
An external amplifier can also be used to extend the output volt-
age swing beyond the power supply rails of the AD8801/AD8803.
This technique permits an easy digital interface for the DAC,
while expanding the output swing to take advantage of higher
voltage external power supplies. For example, DAC A of Fig-
ure 24 is configured to swing from –5 V to +5 V. The actual
output voltage is given by:
Where D is the DAC input value (i.e., 0 to 255). This circuit
can be combined with the “fine/coarse” circuit of Figure 23 if,
for example, a very accurate adjustment around 0 V is desired.
DAC B of Figure 24 is in a noninverting gain of two configura-
tion, which increases the available output swing to +10 V. The
feedback resistors can be adjusted to provide any scaling of the
output voltage, within the limits of the external op amp power
supplies.
V
REFL
V
Figure 23. Buffering the AD8801/AD8803 Output
REFH
Figure 24. Increasing Output Voltage Swing
V
V
V
V
V
V
H
L
H
L
H
L
GND
+5V
V
+5V
GND
DD
V
AD8801/
AD8801/
AD8803
AD8803
V
DD
OUT
DIGITAL INTERFACING
OMITTED FOR CLARITY
A
B
V
V
REFL
REFH
1
R1
100k
R
R
100k
F
S
R
OP193
S
256
100k
D
+12V
100k
100k
+5V
–5V
OP291
R
F
OP191
5 V – 5 V
–5V TO +4.98V
0V TO +10V
SIMPLE BUFFER
0V TO 5V
SUMMER CIRCUIT
WITH FINE TRIM
ADJUSTMENT
–9–
Microcomputer Interfaces
The AD8801/AD8803 serial data input provides an easy inter-
face to a variety of single-chip microcomputers ( Cs). Many Cs
have a built-in serial data capability that can be used for com-
municating with the DAC. In cases where no serial port is pro-
vided, or it is being used for some other purpose (such as an
RS-232 communications interface), the AD8801/AD8803 can
easily be addressed in software.
Eleven data bits are required to load a value into the AD8801/
AD8803 (3 bits for the DAC address and 8 bits for the DAC
value). If more than 11 bits are transmitted before the Chip Se-
lect input goes high, the extra (i.e., the most-significant) bits are
ignored. This feature is valuable because most Cs only transmit
data in 8-bit increments. Thus, the C will send 16 bits to the
DAC instead of 11 bits. The AD8801/AD8803 will only re-
spond to the last 11 bits clocked into the SDI input, however, so
the serial data interface is not affected.
An 8051 C Interface
A typical interface between the AD8801/AD8803 and an 8051
serial port. The serial port is programmed for Mode 0 opera-
tion, which functions as a simple 8-bit shift register. The 8051’s
Port3.0 pin functions as the serial data output, while Port3.1
serves as the serial clock.
Figure 25. Interfacing the 8051 C to an AD8801/AD8803,
Using the Serial Port
When data is written to the Serial Buffer Register (SBUF, at
Special Function Register location 99
cally converted to serial format and clocked out via Port3.0 and
Port3.1. After 8 bits have been transmitted, the Transmit Inter-
rupt flag (SCON.1) is set and the next 8 bits can be transmitted.
The AD8801 and AD8803 require the Chip Select to go low at
the beginning of the serial data transfer. In addition, the SCLK
input must be high when the Chip Select input goes high at the
end of the transfer. The 8051’s serial clock meets this require-
ment, since Port3.1 both begins and ends the serial data in the
high state.
Software for the 8051 Interface
A software routine for the AD8801/AD8803 to 8051 interface is
shown in Listing 1. The routine transfers the 8-bit data stored at
data memory location DAC_VALUE to the AD8801/AD8803
DAC addressed by the contents of location DAC_ADDR.
C is shown in Figure 25. This interface uses the 8051’s internal
SBUF
8051 µC
PORT 1
SERIAL DATA SHIFT REGISTER
SHIFT CLOCK
1.3
1.2
1.1
RxD
TxD
AD8801/AD8803
P3.0
P3.1
P1.3
P1.2
P1.1
H
), the data is automati-
SDI
SCLK
RESET
SHDN
CS
+5V
V
DD
AD8801
V
GND
REFH
0.1µF
O1
O2
O3
O4
O5
O6
O7
O8
10µF
+