EP3C120F780I7 Altera, EP3C120F780I7 Datasheet - Page 73

• Manufacturer Part Number: EP3C120F780I7
• Description: IC CYCLONE III FPGA 120K 780FBGA
• Manufacturer: Altera
• Series: Cyclone® IIIr

Specifications of EP3C120F780I7

• Number Of Logic Elements/cells: 119088
• Number Of Labs/clbs: 7443
• Total Ram Bits: 3981312
• Number Of I /o: 531
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 780-FBGA
• Family Name: Cyclone III
• Number Of Logic Blocks/elements: 119088
• # I/os (max): 531
• Frequency (max): 437.5MHz
• Process Technology: 65nm
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 119088
• Ram Bits: 3981312
• Operating Supply Voltage (min): 1.15V
• Operating Supply Voltage (max): 1.25V
• Operating Temp Range: -40C to 100C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 780
• Package Type: FBGA
• For Use With: 544-2589 - KIT DEV EMB CYCLONE III EDITION544-2566 - KIT DEV DSP CYCLONE III EDITION544-2444 - KIT DEV CYCLONE III EP3C120
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Not Compliant

Chapter 5: Clock Networks and PLLs in the Cyclone III Device Family
PLLs in the Cyclone III Device Family
PLLs in the Cyclone III Device Family
© December 2009
f
Altera Corporation
Altera recommends using the clkena signals when switching the clock source to the
PLLs or the GCLK. The recommended sequence is:
1. Disable the primary output clock by deasserting the clkena signal.
2. Switch to the secondary clock using the dynamic select signals of the clock control
3. Allow some clock cycles of the secondary clock to pass before reasserting the
The Cyclone III device family offers up to four PLLs that provide robust clock
management and synthesis for device clock management, external system clock
management, and high-speed I/O interfaces.
For more information about the number of PLLs in each device density, refer to the
Cyclone III Device Family Overview
The Cyclone III device family PLLs have the same core analog structure.
Table 5–3
Table 5–3. Cyclone III Device Family PLL Hardware Features
C (output counters)
M, N, C counter sizes
Dedicated clock outputs
Clock input pins
Spread-spectrum input clock tracking
PLL cascading
Compensation modes
Phase shift resolution
Programmable duty cycle
Output counter cascading
Input clock switchover
User mode reconfiguration
Loss of lock detection
Notes to
(1) C counters range from 1 through 512 if the output clock uses a 50% duty cycle. For any output clocks using a
(2) Only applicable if the input clock jitter is in the input jitter tolerance specifications.
(3) The smallest phase shift is determined by the voltage-controlled oscillator (VCO) period divided by eight. For
block.
clkena signal. The exact number of clock cycles you must wait before enabling
the secondary clock is design-dependent. You can build custom logic to ensure
glitch-free transition when switching between different clock sources.
non-50% duty cycle, the post-scale counters range from 1 through 256.
degree increments, the Cyclone III device family can shift all output frequencies in increments of at least 45°.
Smaller degree increments are possible depending on the frequency and divide parameters.
Table
lists the features available in the Cyclone III device family PLLs.
5–3:
Hardware Features
chapter.
5
1 to 512
1 single-ended or 1 differential pair
4 single-ended or 2 differential pairs
Through GCLK
Source-Synchronous Mode, No Compensation
Mode, Normal Mode, and Zero Delay Buffer Mode
Down to 96-ps increments
(1)
Cyclone III Device Handbook, Volume 1
Availability
v
v
v
v
v
v
(2)
(3)
5–9