20-101-0732 Rabbit Semiconductor, 20-101-0732 Datasheet - Page 22
20-101-0732
Manufacturer Part Number
20-101-0732
Description
INTERFACE SMART SCREEN OP7100
Manufacturer
Rabbit Semiconductor
Datasheet
1.101-0303.pdf
(126 pages)
Specifications of 20-101-0732
Module/board Type
Single Board Computer Module
For Use With/related Products
OP7100
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
20-101-732
20-101-732
20-101-732
- Current page: 22 of 126
- Download datasheet (780Kb)
Running Dynamic C
Double-click the Dynamic C icon to start the software. Note that the PC
attempts to communicate with the OP7100 each time Dynamic C is started.
No error messages are displayed once communication is established.
The communication rate, port, and protocol are all selected by choosing
Serial Options
OP7100 both set their baud rate automatically to match the communication
rate set on the host PC using Dynamic C (9600 bps, 19,200 bps, 28,800 bps,
or 57,600 bps). To begin, adjust the communications rate to 19,200 bps.
Make sure that the PC serial port used to connect the serial cable (COM1
or COM2) is the one selected in the Dynamic C
the 1-stop-bit protocol.
At this point, the LCD should be blank and the backlight should be off.
Once communication is established, load the sample program
DEFDEMOL.C
and run the program by pressing
menu.
The OP7100 should now alternately display the large font (17x × 35h) and
the small font (6w × 8h). The fonts should scroll across the display.
22 Getting Started
See Appendix A, “Troubleshooting,” if an error message such
as
Once the necessary changes have been made to establish
communication between the host PC and the OP7100, use the
Dynamic C shortcut
communication.
Compiling and running this sample program will overwrite the
demonstration program shown in Figure 2-3.
in the Dynamic C
Target Not Responding
from Dynamic C’s
SAMPLES\QVGA
<Ctrl Y>
F9
OPTIONS
or by selecting
or
to reset the controller and initiate
Communication Error
menu. The SIB and the
OPTIONS
subdirectory. Compile
Run
from the
menu. Select
Run
appears.
OP7100
Related parts for 20-101-0732
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: