ADE7566ASTZF8 Analog Devices Inc, ADE7566ASTZF8 Datasheet - Page 31

• Manufacturer Part Number: ADE7566ASTZF8
• Description: IC ENERGY METER MCU 8K 64LQFP
• Manufacturer: Analog Devices Inc

Specifications of ADE7566ASTZF8

• Applications: Energy Measurement
• Core Processor: 8052
• Program Memory Type: FLASH (8 kB)
• Controller Series: ADE75xx
• Ram Size: 512 x 8
• Interface: I²C, SPI, UART
• Number Of I /o: 20
• Voltage - Supply: 3.135 V ~ 3.465 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 64-LQFP
• Ic Function: Single Phase Energy Measurement IC
• Supply Voltage Range: 3.13V To 3.46V, 2.4V To 3.7V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: LQFP
• No. Of Pins: 64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Preliminary Technical Data
OPERATING MODES
PSM0 (NORMAL MODE)
In PSM0, normal operating mode, V
of the analog and digital circuitry powered by V
are enabled by default. In normal mode, the default clock
frequency, f
reset, is 1.024 MHz.
PSM1 (BATTERY MODE)
In PSM1, battery mode, V
mode, the 8052 core and all of the digital circuitry are enabled
by default. The analog circuitry for the ADE energy metering
DSP powered by V
matically restarts once the V
the PWRDN bit in the MODE1 Register (0x0B) is cleared.
The default f
reset or software reset, is 1.024 MHz.
PSM2 (SLEEP MODE)
PSM2 is a low power consumption sleep mode for use in battery
operation. In this mode, VSW is connected to VBAT. All of the
2.5 V digital and analog circuitry powered through V
are disabled, including the MCU core, resulting in the
following:
Table 25. SFR Maintained in PSM2
I/O Configuration
Interrupt Pins Configuration SFR
(INTPR, 0xFF)
Peripheral Configuration SFR
(PERIPH, 0xF4)
Port 0 Weak Pull-Up Enable SFR
(PINMAP0, 0xB2)
Port 1 Weak Pull-Up Enable SFR
(PINMAP1, 0xB3)
Port 2 Weak Pull-Up Enable SFR
(PINMAP2, 0xB4)
Scratch Pad 1 SFR (SCRATCH1, 0xFB)
Scratch Pad 2 SFR (SCRATCH2, 0xFC)
Scratch Pad 3 SFR (SCRATCH3, 0xFD)
Scratch Pad 4 SFR (SCRATCH4, 0xFE)
CORE
CORE
, established during a power-on reset or software
for PSM1, established during a power-on
INTA
is disabled. This analog circuitry auto-
SW
is connected to V
DD
supply is above 2.75 V and if
Power Supply Monitoring
Battery Detection Threshold SFR
(BATVTH, 0xFA)
Battery Switchover Configuration SFR
(BATPR, 0xF5)
Battery ADC Value SFR (BATADC, 0xDF)
Peripheral ADC Strobe Period SFR
(STRBPER, 0xF9)
Temperature and Supply Delta SFR
(DIFFPROG, 0xF3)
VDCIN ADC Value SFR (VDCINADC, 0xEF)
Temperature ADC Value SFR
(TEMPADC, 0xD7)
–
–
SW
is connected to V
BAT
. In this operating
INTD
INTA
and V
and V
DD
INTA
. All
Rev. PrA | Page 31 of 136
INTD
–
RTC Peripherals
RTC Nominal Compensation SFR
(RTCCOMP, 0xF6)
RTC Temperature Compensation SFR
(TEMPCAL, 0xF7)
RTC Configuration SFR (TIMECON, 0xA1)
Hundredths of a Second Counter SFR
(HTHSEC, 0xA2)
Seconds Counter SFR (SEC, 0xA3)
Minutes Counter SFR (MIN, 0xA4)
Hours Counter SFR (HOUR, 0xA5)
Alarm Interval SFR (INTVAL, 0xA6)
•
•
The 3.3 V peripherals (temperature ADC, VDCIN ADC, RTC,
and LCD) are active in PSM2. They can be enabled or disabled
to reduce power consumption and are configured for PSM2
operation when the MCU core is active (see Table 26 for more
information about the individual peripherals and their PSM2
configuration). The ADE7566/ADE7569 remain in PSM2 until
an event occurs to wake it up.
In PSM2, the ADE7566/ADE7569 provide four scratch pad
RAM SFRs that are maintained during this mode. These SFRs
can be used to save data from PSM0 or PSM1 when entering
PSM2 (see Table 18 to Table 22).
In PSM2, the ADE7566/ADE7569 maintain some SFRs (see
Table 25). The SFRs that are not listed in this table should be
restored when the part enters PSM0 or PSM1 from PSM2.
The RAM in the MCU is no longer valid.
The program counter for the 8052, also held in volatile
memory, becomes invalid when the 2.5 V supply is shut
down. Therefore, the program does not resume from
where it left off, but always starts from the power-on reset
vector when the ADE7566/ADE7569 come out of PSM2.
ADE7566/ADE7569
LCD Peripherals
LCD Segment Enable 2 SFR
(LCDSEGE2, 0xED)
LCD Configuration Y SFR
(LCDCONY, 0xB1)
LCD Configuration X SFR
(LCDCONX, 0x9C)
LCD Configuration SFR (LCDCON,
0x95)
LCD Clock SFR (LCDCLK, 0x96)
LCD Segment Enable SFR
(LCDSEGE, 0x97)
LCD Pointer SFR (LCDPTR, 0xAC)
LCD Data SFR (LCDDAT, 0xAE)
–