NE1617DS NXP Semiconductors, NE1617DS Datasheet

no-image

NE1617DS

Manufacturer Part Number
NE1617DS
Description
Board Mount Temperature Sensors I2C LOC +/- 2OC AND REM +/- 3OC TS
Manufacturer
NXP Semiconductors
Datasheet

Specifications of NE1617DS

Full Temp Accuracy
+/- 3 C, +/- 5 C
Package / Case
SSOP-16
Digital Output - Bus Interface
2-Wire
Maximum Operating Temperature
+ 120 C
Minimum Operating Temperature
0 C
Output Type
Digital
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
NE1617DS,112

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
NE1617DS
Manufacturer:
LRC
Quantity:
15 562
Part Number:
NE1617DS
Manufacturer:
PHI
Quantity:
1 680
Part Number:
NE1617DS
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Product data sheet
Supersedes data of 2003 Nov 25
NE1617
Temperature monitor for
microprocessor systems
INTEGRATED CIRCUITS
2004 Oct 06

Related parts for NE1617DS

NE1617DS Summary of contents

Page 1

NE1617 Temperature monitor for microprocessor systems Product data sheet Supersedes data of 2003 Nov 25 INTEGRATED CIRCUITS 2004 Oct 06 ...

Page 2

Philips Semiconductors Temperature monitor for microprocessor systems FEATURES Replacement for Maxim MAX1617 and Analog Devices ADM1021 Monitors local and remote temperature Accuracy – local (on-chip) sensor – remote sensor No calibration required Programmable over/under temperature alarm ...

Page 3

... Philips Semiconductors Temperature monitor for microprocessor systems ORDERING INFORMATION PART NUMBER NE1617DS SSOP16: plastic shrink small outline package; 16 leads; body width 3.9 mm; lead pitch 0.635 mm FUNCTIONAL BLOCK DIAGRAM NE1617A LOCAL TEMP CONTROL SENSOR LOGIC D+ A-TO-D ANALOG CONVERTER MUX D– ADD1 ADD0 ...

Page 4

Philips Semiconductors Temperature monitor for microprocessor systems TYPICAL OPERATING CIRCUIT REMOTE SENSOR SHIELDED TWISTED PAIR (NOTE 1) NOTES: 1. May be required if remote diode noisy environment and/or several feet from the NE1617. 2. May be required ...

Page 5

Philips Semiconductors Temperature monitor for microprocessor systems ELECTRICAL CHARACTERISTICS +125 C unless otherwise noted. DD amb PARAMETER PARAMETER Temperature resolution Local temperature error Local temperature error Remote temperature error Remote temperature ...

Page 6

Philips Semiconductors Temperature monitor for microprocessor systems SMBUS INTERFACE AC SPECIFICATIONS +125 C unless otherwise noted. DD amb These specifications are guaranteed by design and not tested in ...

Page 7

Philips Semiconductors Temperature monitor for microprocessor systems TYPICAL PERFORMANCE CHARACTERISTICS GND 5 0 – –10 –15 – LEAKAGE RESISTANCE (M ) Figure 4. Temperature error vs. PC board resistance ...

Page 8

Philips Semiconductors Temperature monitor for microprocessor systems 100 100 SMB CLK FREQUENCY (kHz) Figure 8. Standby supply current vs. clock frequency @ 125 ...

Page 9

Philips Semiconductors Temperature monitor for microprocessor systems FUNCTIONAL DESCRIPTION The NE1617 contains an integrating A-to-D converter, an analog multiplexer, a status register, digital data registers, SMBUS interface, associated control logic and a local temperature sensor or channel. The remote diode-type ...

Page 10

Philips Semiconductors Temperature monitor for microprocessor systems TEMPERATURE MONITOR WITH SMB SERIAL INTERFACE Serial bus interface The device can be connected to a standard 2-wire serial interface System Management Bus (SMBus slave device under the control of a ...

Page 11

Philips Semiconductors Temperature monitor for microprocessor systems Configuration register The configuration register is used to mask the Alert interrupt and/or to put the device in software standby mode. Only two bits 6 and 7 of this register are used as ...

Page 12

Philips Semiconductors Temperature monitor for microprocessor systems Status register The content of the status register reflects condition status resulting from all of these activities: comparisons between temperature measurements and temperature limits, the status of ADC conversion, and the hardware condition ...

Page 13

Philips Semiconductors Temperature monitor for microprocessor systems Power-up default condition Upon power-up reset (power is switched off-on), the NE1617 goes into this default condition: – Interrupt latch is cleared, the ALERT output is pulled high by the external pull-up resistor. ...

Page 14

Philips Semiconductors Temperature monitor for microprocessor systems PC BOARD LAYOUT CONSIDERATION Because the NE1617 is used to measure a very small voltage from the remote sensor, care must be taken to minimize noise induced at the sensor inputs, especially in ...

Page 15

Philips Semiconductors Temperature monitor for microprocessor systems SSOP16: plastic shrink small outline package; 16 leads; body width 3.9 mm; lead pitch 0.635 mm 2004 Oct 06 15 Product specification NE1617 SOT519-1 ...

Page 16

Philips Semiconductors Temperature monitor for microprocessor systems REVISION HISTORY Rev Date Description _5 20041006 Product data sheet (9397 750 12383). Supersedes data of 2003 Nov 25 (9397 750 12383). Modifications: Page 12, section “SMBus Alert” added. _4 20031125 Product data ...

Related keywords