ICS1893CKILF IDT, Integrated Device Technology Inc, ICS1893CKILF Datasheet - Page 36

• Manufacturer Part Number: ICS1893CKILF
• Description: PHYCEIVER LOW PWR 3.3V 56-MLF2
• Manufacturer: IDT, Integrated Device Technology Inc
• Series: PHYceiver™r
• Type: PHY Transceiverr

Specifications of ICS1893CKILF

• Protocol: MII
• Voltage - Supply: 3.14 V ~ 3.47 V
• Mounting Type: Surface Mount
• Package / Case: 56-VQFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Drivers/receivers: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 1893CKILF; 800-1023

6.5.6 10Base-T Operation: Smart Squelch
ICS1893CF, Rev. K, 05/13/10
When the 10Base-T link is:
•
•
•
Note:
1. An ICS1893CF receives ‘valid data’ when its Twisted-Pair Receiver phase-locked loop can acquire lock
2. When a link is invalid and the Link Monitor Function detects the presence of data, the ICS1893CF does
3. Enabling or disabling the Smart Squelch Function affects the Link Monitor function.
4. A transition from the invalid state to the valid state does not automatically update the latching-low Link
The Smart Squelch Function imposes more stringent requirements on the Link Monitor Function regarding
the definition of a valid link, thereby providing a level of insurance that spurious noise is not mistaken for a
valid link during cable installation.
An STA can control the execution of the ICS1893CF Smart Squelch Function using bit 18.0 (the Smart
Squelch Inhibit bit in the 10Base-T Operations Register). When bit 18.0 is logic:
•
•
In 10Base-T mode, an ICS1893CF appends an IDL to the end of each packet during data transmission.
The receiving PHY (the remote link partner) sees this IDL and removes it from the data stream.
Invalid, and the Smart Squelch function is:
Valid, and the Smart Squelch function is:
Valid, the Link Monitor Function declares the link as invalid if it receives neither data nor NLPs (that is,
the link shows either no activity or inconsistent activity) for more than 81 to 83 ms. In this case the Link
Monitor Function sets the Link Status bit to logic zero.
Zero (the default), an ICS1893CF enables its Smart Squelch Function. In this case, the Link Monitor
must confirm the presence of both data and a valid IDL at the end of the packet before declaring a link
valid.
One, an ICS1893CF disables or inhibits its Smart Squelch Function. In this case, the Link Monitor does
not have to confirm the presence of an IDL to declare a link valid (that is, the reception of any data is
sufficient).
– Disabled (bit 18.0 is logic one), the Link Monitor Function must detect at least one of the following
– Enabled (bit 18.0 is logic zero), the Link Monitor Function must detect at least one of the following
– Disabled (bit 18.0 is logic one), the Link Monitor Function continues to report its link as valid as long
– Enabled (bit 18.0 is logic zero), the Link Monitor Function continues to report its link as valid as long
and extract the receive clock from the incoming data stream for a minimum of three consecutive bit
times.
not transition the link to the valid state until after the reception of the present packet is complete.
Status bit.
events before transitioning its link from the invalid state to the valid state:
events before transitioning its link from the invalid state to the valid state:
as it continues to detect any of the following:
as it continues to detect any of the following:
• More than seven, ISO/IEC-defined, Normal Link Pulses (NLPs)
• Any valid data
• More than seven, ISO/IEC-defined, Normal Link Pulses (NLPs)
• Any valid data followed by a valid IDL
• ISO/IEC-defined, Normal Link Pulses (NLPs)
• Any valid data
• ISO/IEC-defined, Normal Link Pulses (NLPs)
• Any valid data followed by a valid IDL
ICS1893CF Data Sheet - Release
Copyright © 2009, Integrated Device Technology, Inc.
All rights reserved.
36
Chapter 6 Functional Blocks
May, 2010