DSPIC33FJ256GP710-I/PF Microchip Technology Inc., DSPIC33FJ256GP710-I/PF Datasheet - Page 86

• Manufacturer Part Number: DSPIC33FJ256GP710-I/PF
• Description: 16 BIT MCU/DSP 100LD 40MIPS 256KB FLASH
• Manufacturer: Microchip Technology Inc.
• Type: DSPr

Specifications of DSPIC33FJ256GP710-I/PF

• A/d Inputs: 32-Channels, 12-Bit
• Comparators: 8
• Cpu Speed: 40 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 85
• Interface: CAN/I2C/SPI/UART
• Ios: 85
• Memory Type: Flash
• Number Of Bits: 16
• Package Type: 100-pin TQFP
• Programmable Memory: 256K Bytes
• Ram Size: 30K Bytes
• Timers: 9-16-bit, 4-32-bit
• Voltage, Range: 3-3.6
• Lead Free Status / Rohs Status: RoHS Compliant part

dsPIC33F
REGISTER 5-1:
DS70165D-page 84
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13-9
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
Note 1:
TRAPR
R/W-0
R/W-0
EXTR
2:
All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not
cause a device Reset.
If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the
SWDTEN bit setting.
TRAPR: Trap Reset Flag bit
1 = A Trap Conflict Reset has occurred
0 = A Trap Conflict Reset has not occurred
IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit
1 = An illegal opcode detection, an illegal address mode or uninitialized W register used as an
0 = An illegal opcode or uninitialized W Reset has not occurred
Unimplemented: Read as ‘0’
VREGS: Voltage Regulator Standby During Sleep bit
1 = Voltage regulator goes into Standby mode during Sleep
0 = Voltage regulator is active during Sleep
EXTR: External Reset (MCLR) Pin bit
1 = A Master Clear (pin) Reset has occurred
0 = A Master Clear (pin) Reset has not occurred
SWR: Software Reset (Instruction) Flag bit
1 = A RESET instruction has been executed
0 = A RESET instruction has not been executed
SWDTEN: Software Enable/Disable of WDT bit
1 = WDT is enabled
0 = WDT is disabled
WDTO: Watchdog Timer Time-out Flag bit
1 = WDT time-out has occurred
0 = WDT time-out has not occurred
SLEEP: Wake-up from Sleep Flag bit
1 = Device has been in Sleep mode
0 = Device has not been in Sleep mode
IDLE: Wake-up from Idle Flag bit
1 = Device was in Idle mode
0 = Device was not in Idle mode
BOR: Brown-out Reset Flag bit
1 = A Brown-out Reset has occurred
0 = A Brown-out Reset has not occurred
IOPUWR
R/W-0
R/W-0
SWR
Address Pointer caused a Reset
RCON: RESET CONTROL REGISTER
W = Writable bit
‘1’ = Bit is set
SWDTEN
R/W-0
U-0
—
(2)
WDTO
R/W-0
U-0
Preliminary
—
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
SLEEP
R/W-0
(2)
U-0
—
(1)
R/W-0
IDLE
U-0
—
© 2006 Microchip Technology Inc.
x = Bit is unknown
R/W-1
BOR
U-0
—
VREGS
R/W-0
R/W-1
POR
bit 8
bit 0