VQ1301N-51 SMC Corporation, VQ1301N-51 Datasheet - Page 8

• Manufacturer Part Number: VQ1301N-51
• Description: SOLENOID VALVE, BASE MT, 5 PORT, PLUG-IN TYPE, 24VDC, 3 POSITION CLOSED CENTER
• Manufacturer: SMC Corporation
• Type: Solenoidr

Specifications of VQ1301N-51

• Brand/series: VQ Series
• Configuration: 3-Position Closed Center
• Enclosure Rating: IP65
• Fluid Type: Air/Inert Gas
• Number Of Ports: 5
• Pressure, Operating: 0.7 MPa
• Primary Type: Solenoid Valve
• Temperature, Ambient: –10° to +50°C
• Valve Type: 5-Port Solenoid, Plug-In, Base Mounted with 3 Position Closed Center Actuation, Rubber Seal, Negative Common
• Voltage, Coil: 24 VDC

7
Kit type/Electrical entry/Cable length
Cylinder port
Connector entry direction
Top entry Side entry
Symbol
CM
Note 1)
kit
F
F
M5
C3
C4
C6
25P
L3
L4
L6
Note 1)
U0
U1
U2
U3
Note 1) Indicate “Mixed sizes and with port plug” by means of the manifold specification sheet.
Note 2) When selecting the mixed size for different types of piping or dual flow fitting assembly,
Note 3) Inch-size one-touch fittings are also available. Refer to page 57 for details.
Note 4) M5 fittings for M5 thread are attached without being incorporated.
Note 1) Besides the above, F/P kit with different number of pins are available. Refer to page 55 for details.
Note 2) Refer to page 56 for details.
Simple specials are available with SMC Simple Specials System.
Refer to Best Pneumatics No. q for details on applicable models.
With ø3.2 one-touch fitting
With ø4 one-touch fitting
With ø6 one-touch fitting
M5 thread
Mixed sizes and with port plug
Top ported elbow with ø3.2 one-touch fitting
Top ported elbow with ø4 one-touch fitting
Top ported elbow with ø6 one-touch fitting
kit
kit
(D-sub connector)
F
S0
S1
S2
S3
enter “MM” and give instructions in the manifold specification sheet.
Top entry
VV5Q 1 1 08 C6
Without cable
With cable (1.5 m)
With cable (3 m)
With cable (5 m)
1
Port size
1
Series
VQ1000
Side entry
P. 17
Manifold
Plug-in unit
The number of max. stations
differs from kit to kit.
(Refer to the below table.)
01
Series
Note 2)
2 to 24
stations
Plug-in Unit
Base Mounted
Stations
Connector entry direction
Top entry
Note 1)
1 station
P
kit
P
26P
U0
U1
U2
U3
Symbol
MM
LM
Side entry
B3
B4
B6
B5
kit
(Flat ribbon cable)
kit
L5
P
Note 1)
Note 2)
S0
S1
S2
S3
Top entry
Top ported elbow M5 thread
Bottom ported elbow with ø3.2 one-touch fitting
Bottom ported elbow with ø4 one-touch fitting
Bottom ported elbow with ø6 one-touch fitting
Bottom ported elbow M5 thread
Elbow port, mixed sizes
Mixed size for different types of piping, option installed
Without cable
With cable (1.5 m)
With cable (3 m)
With cable (5 m)
How to Order Manifold
F
P. 21
Side entry
Kit type
Port size
U1
VQ1000
Note 2)
2 to 24
stations
Connector entry direction
Top entry
20P
kit
J
J
U0
U1
U2
U3
Side entry
kit
(Flat ribbon cable
20P)
kit
J
S0
S1
S2
S3
Top entry
Without cable
With cable (1.5 m)
With cable (3 m)
With cable (5 m)
CE compliant
DC specification only
Nil
Q
D„
J„
G1
G2
G3
Option
B
K
R
Symbol
CE compliant
D0
Nil
Note 2)
Note 5)
Note 6)
D
N
S
2
Note 3)
Note 3)
Note 3)
Note 4)
Note 7)
P. 25
Note 1) When two or more symbols are specified, indi-
Note 2) Models with a suffix “-B” have check valves for
Note 3) Specify the mounting position by means of the
Note 4) Refer to page 69 for details on with vacuum
Note 5) Specify the wiring specifications by means of
Note 6) Indicate “R” for the valve with external pilot.
Note 7) „: Station. Example: D08: The number of sta-
Side entry
—
Note 2)
2 to 16
stations
Special wiring spec. (Except double wiring)
cate them alphabetically. Example: -BRS
prevention of back pressure at all manifold
stations. When a back pressure check valve is
desired, and is to be installed only in certain
manifold stations, specify the mounting position
by means of the manifold specification sheet.
manifold specification sheet.
ejector unit. A combination of “J” and “N” is not
available.
the manifold specification sheet. (Except L kit)
tions that may be displayed is longer than the
manifold number of stations.
With DIN rail bracket (Without DIN rail)
Direct EXH outlet with built-in silencer
200/220 VAC models (F/L kit only)
G
kit
With back pressure check valve
G
DIN rail length specified
2 sets of regulator unit
3 sets of regulator unit
1 set of regulator unit
0
1
2
3
DIN rail mounting
With name plate
With ejector unit
kit
(Flat ribbon cable
with terminal block)
External pilot
Without cable
With cable (1.5 m)
With cable (3 m)
With cable (5 m)
Option
None
20P
The voltage used for
the valve is 24 VDC.
Order separately
SI unit made by
OMRON Corp.
P. 29
[Option]
2 to 16
stations
Note 2)