PIC16F777-I/P Microchip Technology Inc., PIC16F777-I/P Datasheet - Page 33

• Manufacturer Part Number: PIC16F777-I/P
• Description: 40 PIN, 14 KB FLASH, 368 RAM, 36 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F777-I/P

• A/d Inputs: 14-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 5 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 36
• Interface: I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 40-pin PDIP
• Programmable Memory: 14K Bytes
• Ram Size: 368 Bytes
• Speed: 20 MHz
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

4.0
Some pins for these I/O ports are multiplexed with an
alternate function for the peripheral features on the
device. In general, when a peripheral is enabled, that
pin may not be used as a general purpose I/O pin.
Additional information on I/O ports may be found in the
PICmicro™
(DS33023).
4.1
PORTA is a 6-bit wide, bi-directional port. The corre-
sponding data direction register is TRISA. Setting a
TRISA bit (= ‘1’) will make the corresponding PORTA
pin an input (i.e., put the corresponding output driver in
a Hi-Impedance mode). Clearing a TRISA bit (= ‘0’) will
make the corresponding PORTA pin an output (i.e., put
the contents of the output latch on the selected pin).
Reading the PORTA register reads the status of the
pins, whereas writing to it will write to the port latch. All
write operations are read-modify-write operations.
Therefore, a write to a port implies that the port pins are
read, the value is modified and then written to the port
data latch.
Pin RA4 is multiplexed with the Timer0 module clock
input to become the RA4/T0CKI pin. The RA4/T0CKI
pin is a Schmitt Trigger input and an open drain output.
All other PORTA pins have TTL input levels and full
CMOS output drivers.
Other PORTA pins are multiplexed with analog inputs
and analog V
selected by clearing/setting the control bits in the
ADCON1 register (A/D Control Register1).
The TRISA register controls the direction of the RA
pins, even when they are being used as analog inputs.
The user must ensure the bits in the TRISA register are
maintained set, when using them as analog inputs.
EXAMPLE 4-1:
 2002 Microchip Technology Inc.
BCF
BCF
CLRF
BSF
MOVLW
MOVWF
MOVLW
MOVWF
Note:
I/O PORTS
PORTA and the TRISA Register
STATUS, RP0
STATUS, RP1
PORTA
STATUS, RP0
0x06
ADCON1
0xCF
TRISA
On a Power-on Reset, these pins are con-
figured as analog inputs and read as '0'.
REF
Mid-Range
input. The operation of each pin is
INITIALIZING PORTA
;
; Bank0
; Initialize PORTA by
; clearing output
; data latches
; Select Bank 1
; Configure all pins
; as digital inputs
; Value used to
; initialize data
; direction
; Set RA<3:0> as inputs
; RA<5:4> as outputs
; TRISA<7:6>are always
; read as ’0’.
Reference
Manual,
FIGURE 4-1:
FIGURE 4-2:
Data Bus
WR Port
WR TRIS
RD TRIS
RD PORT
Note 1: I/O pins have protection diodes to V
Data Bus
WR PORT
WR TRIS
RD TRIS
RD PORT
Note 1: I/O pin has protection diodes to V
To A/D Converter
TMR0 Clock Input
TRIS Latch
Data Latch
D
D
CK
CK
TRIS Latch
Data Latch
D
D
CK
CK
Q
Q
Q
Q
Q
Q
Q
Q
BLOCK DIAGRAM OF
RA3:RA0 AND RA5 PINS
BLOCK DIAGRAM OF
RA4/T0CKI PIN
Q
PIC16F7X
Q
EN
EN
Analog
Input
Mode
EN
D
EN
Schmitt
Trigger
Input
Buffer
D
SS
DS30325B-page 31
N
V
DD
only.
SS
V
P
N
V
DD
SS
and V
TTL
Input
Buffer
SS
I/O pin
I/O pin
.
(1)
(1)