PIC18F24J10-I/SS Microchip Technology Inc., PIC18F24J10-I/SS Datasheet - Page 25

• Manufacturer Part Number: PIC18F24J10-I/SS
• Description: Microcontroller; 16 KB Flash; 1024 RAM; 0 EEPROM; 21 I/O; 28-Pin-SSOP
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F24J10-I/SS

• A/d Inputs: 10-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 21
• Interface: I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 28-pin SSOP
• Programmable Memory: 16K Bytes
• Ram Size: 1K Bytes
• Speed: 40 MHz
• Timers: 1-8-bit, 2-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

2.0
2.1
The PIC18F45J10 family of devices can be operated in
five different oscillator modes:
1.
2.
3.
4.
5.
Four of these are selected by the user by programming
the FOSC2:FOSC0 configuration bits. The fifth mode
(INTRC) may be invoked under software control; it can
also be configured as the default mode on device
Resets.
2.2
In HS or HSPLL Oscillator modes, a crystal or ceramic
resonator is connected to the OSC1 and OSC2 pins to
establish
connections.
The oscillator design requires the use of a parallel cut
crystal.
© 2006 Microchip Technology Inc.
Note:
HS
HSPLL High-Speed Crystal/Resonator
EC
ECPLL External Clock with Software PLL
INTRC Internal 31 kHz Oscillator
OSCILLATOR
CONFIGURATIONS
Oscillator Types
Crystal Oscillator/Ceramic
Resonators (HS Modes)
oscillation.
Use of a series cut crystal may give a fre-
quency out of the crystal manufacturer’s
specifications.
High-Speed Crystal/Resonator
with Software PLL Control
External Clock with F
Control
Figure 2-1
OSC
shows
/4 Output
the
Preliminary
pin
PIC18F45J10 FAMILY
FIGURE 2-1:
TABLE 2-1:
Capacitor values are for design guidance only.
These capacitors were tested with the resonators
listed below for basic start-up and operation. These
values are not optimized.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
V
See the notes following Table 2-2 for additional
information.
Note 1: See Table 2-1 and Table 2-2 for initial values of
DD
Mode
HS
and temperature range for the application.
C1
C2
2: A series resistor (R
3: R
(1)
(1)
Typical Capacitor Values Used:
C1 and C2.
strip cut crystals.
F
16.0 MHz
XTAL
8.0 MHz
varies with the oscillator mode chosen.
Freq.
R
Resonators Used:
S (2)
CAPACITOR SELECTION FOR
CERAMIC RESONATORS
OSC1
OSC2
16.0 MHz
CRYSTAL/CERAMIC
RESONATOR OPERATION
(HS OR HSPLL
CONFIGURATION)
4.0 MHz
8.0 MHz
S
OSC1
) may be required for AT
27 pF
22 pF
R
F
(3)
DS39682B-page 23
PIC18F45J10
Sleep
OSC2
27 pF
22 pF
To
Internal
Logic