PIC18F2520-I/ML Microchip Technology Inc., PIC18F2520-I/ML Datasheet - Page 262
PIC18F2520-I/ML
Manufacturer Part Number
PIC18F2520-I/ML
Description
28 QFN 6x6mm TUBE, 32 KB Flash, 1536 RAM, 25 I/O
Manufacturer
Microchip Technology Inc.
Datasheet
1.PIC18F2520-IML.pdf
(412 pages)
Specifications of PIC18F2520-I/ML
A/d Inputs
10-Channel, 10-Bit
Comparators
2
Cpu Speed
10 MIPS
Eeprom Memory
1K Bytes
Input Output
25
Interface
I2C/SPI/UART/USART
Memory Type
Flash
Number Of Bits
8
Package Type
28-pin QFN
Programmable Memory
32K Bytes
Ram Size
1.5K Bytes
Speed
40 MHz
Temperature Range
–40 to 125 °C
Timers
1-8-bit, 3-16-bit
Voltage, Range
2-5.5 V
Lead Free Status / Rohs Status
RoHS Compliant part
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC18F2520-I/ML
Manufacturer:
MICROCHI
Quantity:
20 000
- Current page: 262 of 412
- Download datasheet (7Mb)
PIC18F2420/2520/4420/4520
23.3
The Two-Speed Start-up feature helps to minimize the
latency period from oscillator start-up to code execution
by allowing the microcontroller to use the INTOSC
oscillator as a clock source until the primary clock
source is available. It is enabled by setting the IESO
Configuration bit.
Two-Speed Start-up should be enabled only if the
primary oscillator mode is LP, XT, HS or HSPLL
(Crystal-Based modes). Other sources do not require
an OST start-up delay; for these, Two-Speed Start-up
should be disabled.
When enabled, Resets and wake-ups from Sleep mode
cause the device to configure itself to run from the
internal oscillator block as the clock source, following
the time-out of the Power-up Timer after a Power-on
Reset is enabled. This allows almost immediate code
execution while the primary oscillator starts and the
OST is running. Once the OST times out, the device
automatically switches to PRI_RUN mode.
To use a higher clock speed on wake-up, the INTOSC
or postscaler clock sources can be selected to provide
a higher clock speed by setting bits, IRCF<2:0>,
immediately after Reset. For wake-ups from Sleep, the
INTOSC or postscaler clock sources can be selected
by setting the IRCF<2:0> bits prior to entering Sleep
mode.
FIGURE 23-2:
DS39631E-page 260
Two-Speed Start-up
Note 1: T
Multiplexer
CPU Clock
PLL Clock
Peripheral
Program
INTOSC
Counter
Output
OSC1
Clock
2: Clock transition typically occurs within 2-4 T
Wake from Interrupt Event
TIMING TRANSITION FOR TWO-SPEED START-UP (INTOSC TO HSPLL)
OST
PC
= 1024 T
Q1
OSC
T
OST (1)
; T
PLL
Q2
PC + 2
= 2 ms (approx). These intervals are not shown to scale.
T
PLL (1)
OSTS bit Set
Q3
Q4
OSC
In all other power-managed modes, Two-Speed Start-
up is not used. The device will be clocked by the
currently selected clock source until the primary clock
source becomes available. The setting of the IESO bit
is ignored.
23.3.1
While using the INTOSC oscillator in Two-Speed Start-
up, the device still obeys the normal command
sequences
including
Section 3.1.4 “Multiple Sleep Commands”). In
practice, this means that user code can change the
SCS<1:0> bit settings or issue SLEEP instructions
before the OST times out. This would allow an
application
“housekeeping” tasks and return to Sleep before the
device starts to operate from the primary oscillator.
User code can also check if the primary clock source is
currently providing the device clocking by checking the
status of the OSTS bit (OSCCON<3>). If the bit is set,
the primary oscillator is providing the clock. Otherwise,
the internal oscillator block is providing the clock during
wake-up from Reset or Sleep mode.
Q1
1
.
Transition
2
Clock
n-1 n
(2)
multiple
SPECIAL CONSIDERATIONS FOR
USING TWO-SPEED START-UP
PC + 4
for
to
briefly
entering
Q2
SLEEP
Q3 Q4
© 2008 Microchip Technology Inc.
wake-up,
power-managed
instructions
Q1
PC + 6
Q2
perform
Q3
(refer
modes,
routine
to
Related parts for PIC18F2520-I/ML
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Microcontroller; 32 KB Flash; 1536 RAM; 256 EEPROM; 25 I/O; 28-Pin-SPDIP
Manufacturer:
Microchip Technology Inc.
Datasheet:
Part Number:
Description:
Microcontroller; 32 KB Flash; 1536 RAM; 256 EEPROM; 25 I/O; 28-Pin-SOIC
Manufacturer:
Microchip Technology Inc.
Datasheet:
Part Number:
Description:
PIC18F With 128-segment LCD Driver And 12-bit ADC, 8KB Flash, 768B RAM, CCP, MSS
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
PIC18F With 128-segment LCD Driver And 12-bit ADC, 16KB Flash, 768B RAM, CCP, MS
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
PIC18F With 192-segment LCD Driver And 12-bit ADC, 8KB Flash, 768B RAM, CCP, MSS
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
PIC18F With 192-segment LCD Driver And 12-bit ADC, 16KB Flash, 768B RAM, CCP, MS
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
Microcontrollers (MCU) 48KB 3328 RAM 52 I/O
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
Microcontrollers (MCU) 64KB 3328 RAM 52 I/O
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm T/R
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 TQFP 10x10x1mm T/R
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
128kB Flash, 4kB RAM, 1kB EE, 16MIPS, NanoWatt XLP, LCD, 5V 80 TQFP 12x12x1mm T/
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm TUBE
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 TQFP 10x10x1mm TRAY
Manufacturer:
Microchip Technology
Part Number:
Description:
128kB Flash, 4kB RAM, 1kB EE, 16MIPS, NanoWatt XLP, LCD, 5V 80 TQFP 12x12x1mm TR
Manufacturer:
Microchip Technology