PIC10F202-I/P Microchip Technology Inc., PIC10F202-I/P Datasheet - Page 52
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
PIC10F202-I/P
Manufacturer Part Number
PIC10F202-I/P
Description
8 PIN, 768 B FLASH, 24 RAM, 4 I/O
Manufacturer
Microchip Technology Inc.
Datasheet
1.PIC10F202-IP.pdf
(88 pages)
Specifications of PIC10F202-I/P
Cpu Speed
1 MIPS
Eeprom Memory
0 Bytes
Frequency
4 MHz
Input Output
4
Memory Type
Flash
Number Of Bits
8
Package Type
8-pin PDIP
Programmable Memory
750 Bytes
Ram Size
24 Bytes
Speed
4 MHz
Timers
1-8-bit
Voltage, Range
2-5.5 V
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC10F202-I/P
Manufacturer:
MICROCHIP
Quantity:
12 000
Company:
Part Number:
PIC10F202-I/P
Manufacturer:
Microchip Technology
Quantity:
1 812
Part Number:
PIC10F202-I/P
Manufacturer:
MICRCOHI
Quantity:
20 000
PIC10F200/202/204/206
9.10
If the code protection bit has not been programmed, the
on-chip program memory can be read out for
verification purposes.
The first 64 locations and the last location (Reset
vector) can be read, regardless of the code protection
bit setting.
9.11
Four memory locations are designated as ID locations
where the user can store checksum or other code
identification numbers. These locations are not
accessible during normal execution, but are readable
and writable during Program/Verify.
Use only the lower 4 bits of the ID locations and always
program the upper 8 bits as ‘0’s.
9.12
The PIC10F200/202/204/206 microcontrollers can be
serially programmed while in the end application circuit.
This is simply done with two lines for clock and data,
and three other lines for power, ground and the
programming voltage. This allows customers to manu-
facture boards with unprogrammed devices and then
program the microcontroller just before shipping the
product. This also allows the most recent firmware or a
custom firmware, to be programmed.
The devices are placed into a Program/Verify mode by
holding the GP1 and GP0 pins low while raising the
MCLR (V
specification). GP1 becomes the programming clock
and GP0 becomes the programming data. Both GP1
and GP0 are Schmitt Trigger inputs in this mode.
After Reset, a 6-bit command is then supplied to the
device. Depending on the command, 16 bits of program
data are then supplied to or from the device, depending
if the command was a Load or a Read. For complete
details of serial programming, please refer to the
PIC10F200/202/204/206 Programming Specifications.
A typical In-Circuit Serial Programming connection is
shown in Figure 9-10.
DS41239C-page 50
Program Verification/Code
Protection
ID Locations
In-Circuit Serial Programming™
PP
) pin from V
IL
to V
IHH
(see programming
Preliminary
FIGURE 9-10:
External
Connector
Signals
Data I/O
CLK
+5V
V
0V
PP
To Normal
Connections
To Normal
Connections
TYPICAL IN-CIRCUIT
SERIAL
PROGRAMMING™
CONNECTION
© 2006 Microchip Technology Inc.
V
V
MCLR/V
GP1
GP0
V
DD
SS
DD
PIC10F20X
PP