71M6541F-IGT/F Maxim Integrated Products, 71M6541F-IGT/F Datasheet - Page 56

• Manufacturer Part Number: 71M6541F-IGT/F
• Description: PMIC Solutions Precision Energy Meter IC
• Manufacturer: Maxim Integrated Products
• Type: Metering SoCr

Specifications of 71M6541F-IGT/F

• Core: 8051
• Core Architecture: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 5 KB
• Device Million Instructions Per Second: 5 MIPS
• Interface Type: I2C, ICE, SPI, UART
• Maximum Clock Frequency: 5 MHz
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Number Of Programmable I/os: 30
• Number Of Timers: 2
• On-chip Adc: 22 bit
• Operating Supply Voltage: 3 V to 3.6 V
• Package / Case: LQFP-64
• Processor Series: 8051
• Program Memory Size: 64 KB
• Program Memory Type: Flash
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

2.5.5 71M654x Temperature Sensor
The 71M654x includes an on-chip temperature sensor for determining the temperature of its bandgap
reference. The primary use of the temperature data is to determine the magnitude of compensation
required to offset the thermal drift in the system for the compensation of current, voltage and energy
measurement and the RTC. See
RTC Temperature Compensation
Unlike earlier generation Teridian SoCs, the 71M654x does not use the ADC to read the temperature
sensor. Instead, it uses a technique that is operational in SLP and LCD mode, as well as BRN and MSN
modes. This means that the temperature sensor can be used to compensate for the frequency variation
of the crystal, even in SLP mode while the MPU is halted. See
on page 53.
In MSN and BRN modes, the temperature sensor is awakened on command from the MPU by setting the
TEMP_START (I/O RAM 0x28B4[6]) control bit. The MPU must wait for the TEMP_START bit to clear before
reading STEMP[10:0] and before setting the TEMP_START bit once again. In SLP and LCD modes, it is
awakened at a regular rate set by TEMP_PER[2:0] (I/O RAM 0x28A0[2:0]).
The result of the temperature measurement can be read from the two I/O RAM locations STEMP[10:3]
(I/O RAM 0x2881) and STEMP[2:0] (I/O RAM 0x2882[7:5]). Note that both of these I/O RAM locations must
be read and properly combined to form the STEMP[10:0] 11-bit value (see STEMP in
resulting 11-bit value is in 2’s complement form and ranges from -1024 to +1023 (decimal). The equations
below are used to calculate the sensed temperature from the 11-bit STEMP[10:0] reading.
The equations below are used to calculate the sensed temperature. The first equation applies when the
71M654x is in MSN mode and TEMP_PWR = 1. The second equation applies when the 71M654x is in
BRN mode, and in this case, the TEMP_PWR and TEMP_BSEL bits must both be set to the same value, so
that the battery that supplies the temperature sensor is also the battery that is measured and reported in
BSENSE. Thus, the second equation requires reading STEMP and BSENSE. In the second equation,
BSENSE (the sensed battery voltage) is used to obtain a more accurate temperature reading when the IC
is in BRN mode.
For the 71M654x in MSN Mode (with TEMP_PWR = 1):
For the 71M654x in BRN Mode, (with TEMP_PWR=TEMP_BSEL):
Table 46
56
TBYTE_BUSY
TEMP_PER[2:0]
Name
measurement may not finish. In this case, firmware may complete the measurement by selecting
V3P3D (TEMP_PWR = 1).
If TEMP_PWR selects VBAT_RTC when the battery is nearly discharged, the temperature
shows the I/O RAM registers used for temperature and battery measurement.
Temp
Table 46: I/O RAM Registers for Temperature and Battery Measurement
(
o
28A0[2:0]
Location
C
28A0[3]
)
=
. 0
© 2008–2011 Teridian Semiconductor Corporation
325
4.7 Metrology Temperature Compensation
⋅
Rst
STEMP
0
0
on page 53.
Temp
Wk
0
–
(
+
°
C
. 0
R/W
)
Dir
R
00208
=
. 0
325
Indicates that hardware is still writing the 0x28A0
byte. Additional writes to this byte are locked out
while it is one. Write duration could be as long as 6 ms.
Sets the period between temperature measurements.
Automatic measurements can be enabled in any
mode (MSN, BRN, LCD, or SLP).
Description
TEMP_PER
⋅
⋅
STEMP
BSENSE
1-6
0
7
+
2.5.4.4 RTC Temperature Compensation
22
2
Time
Manual updates (see TEMP_START)
2 ^ (3+TEMP_PER) (seconds)
Continuous
−
. 0
584
⋅
on page 97. Also see
BSENSE
Table
+
40
46). The
9 .
2.5.4.4
v1.1