71M6543F-IGTR/F Maxim Integrated Products, 71M6543F-IGTR/F Datasheet - Page 35
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
71M6543F-IGTR/F
Manufacturer Part Number
71M6543F-IGTR/F
Description
PMIC Solutions Precision Energy Meter IC
Manufacturer
Maxim Integrated Products
Type
Metering SoCr
Datasheet
1.71M6543F-DB.pdf
(157 pages)
Specifications of 71M6543F-IGTR/F
Core
8051
Core Architecture
8051
Data Bus Width
8 bit
Data Ram Size
5 KB
Device Million Instructions Per Second
5 MIPS
Interface Type
I2C, ICE, SPI, UART
Maximum Clock Frequency
5 MHz
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Number Of Programmable I/os
51
Number Of Timers
2
On-chip Adc
22 bit
Operating Supply Voltage
3 V to 3.6 V
Package / Case
LQFP-100
Processor Series
8051
Program Memory Size
64 KB
Program Memory Type
Flash
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
71M6543F-IGTR/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
All DIO ports on the chip are bi-directional. Each of them consists of a latch (SFR P0 to P3), an output
driver and an input buffer, therefore the MPU can output or read data through any of these ports. Even if
a DIO pin is configured as an output, the state of the pin can still be read by the MPU, for example when
counting pulses issued via DIO pins that are under CE control.
Clock Stretching (CKCON[2:0], SFR 0x8E)
The CKCON[2:0] field defines the stretch memory cycles that are used for MOVX instructions when
accessing external peripherals. The practical value of this register for the 71M6543 is to guarantee access
to XRAM between CE, MPU, and SPI. The default setting of CKCON[2:0] (001) should be changed to 000
for best performance.
Table 15
from 0 to 7. The widths of the signals are counted in MPU clock cycles. The post-reset state of the
CKCON[2:0] field (001), which is shown in bold in the table, performs the MOVX instructions with a
stretch value equal to 1.
2.4.4 Instruction Set
All instructions of the generic 8051 microcontroller are supported. A complete list of the instruction set
and of the associated op-codes is contained in the 71M654x Software User’s Guide (SUG).
2.4.5 80515 Power Reduction Modes
The 80515 core provides two power reduction modes: Idle Mode and Power-Down Mode. These power
saving modes are invoked by setting the appropriate control bit in the PCON SFR register (SFR 0x87).
Idle Mode halts the MPU while allowing the interrupt, timer, and serial port functions to continue to
operate. Once Idle Mode has been entered, an interrupt event automatically ends Idle Mode. After the
interrupt has been serviced, program execution continues with the instruction immediately following the
instruction that set the Idle Mode bit. To enter Idle Mode, the firmware must set the IDL bit (bit 0) in the
PCON SFR register (SFR 0x87).
v1.2
Name
At power-up SEGDIO0-15 are configured as inputs. It is necessary to write PORT_E = 1 (I/O
RAM 0x270C[5]) to enable SEGDIO0-DIO15. The default PORT_E = 0 blocks any momentary
output transient pulses that would otherwise occur when SEGDIO0-15 are reset on power-up.
SFR
shows how the signals of the External Memory Interface change when stretch values are set
P0
P1
P2
P3
CKCON[2:0]
000
001
010
011
100
101
110
111
Address
SFR
80
90
A0
B0
© 2008–2011 Teridian Semiconductor Corporation
Stretch
Table 14: Port Registers (SEGDIO0-15)
Table 15: Stretch Memory Cycle Width
Value
0
1
2
3
4
5
6
7
D7
DIO_DIR[15:12]
memaddr
DIO_DIR[11:8]
DIO_DIR[3:0]
DIO_DIR[7:4]
Read Signal Width
D6
1
2
3
4
5
6
7
8
D5
memrd
71M6543F/H and 71M6543G/GH Data Sheet
1
2
3
4
5
6
7
8
D4
memaddr
Write Signal Width
D3
2
3
4
5
6
7
8
9
D2
DIO[15:11]
DIO[11:8]
DIO[3:0]
DIO[7:4]
memwr
1
1
2
3
4
5
6
7
D1
D0
35