MAX19527EVKIT+ Maxim Integrated Products, MAX19527EVKIT+ Datasheet
MAX19527EVKIT+
Related parts for MAX19527EVKIT+
MAX19527EVKIT+ Summary of contents
Page 1
... S _ On-Board_Clock-Shaping_Circuit_with_Adjustable_ S Duty_Cycle _ On-Board_or_Stand-Alone_SPI™_Interface_Control S _ DCEP_Board_Available S _ Fully_Assembled_and_Tested S PART MAX19527EVKIT+ DCEP +Denotes lead(Pb)-free and RoHS compliant. DESIGNATION C59, C89, C90, C95–C98, C103–C106, C111, C112, C113, C130, C133, C135, C136, C137, C140, C141, C144, C145, C146 C60, C61, C66– ...
Page 2
MAX19527 Evaluation Kit DESIGNATION QTY DESCRIPTION 10FF Q20%, 10V X5R ceramic capacitors (1210) C76, C80, C82 3 TDK C3225X5R1A106M or Murata GRM32ER61A106K 10FF Q20%, 10V X5R ceramic C83, C85, C86, capacitors (0805) 5 C88, C131 TDK C2012X5R1A106K Murata GRM219R61A106K C84, ...
Page 3
DESIGNATION QTY DESCRIPTION UART-to-USB converter U8 1 (32 TQFP) FTDI FT232BL 93C46 type 3-wire EEPROM SO) Atmel AT93C46EN-SH-B Ultra-high-speed U10 1 microcontroller (44 TQFP) Maxim DS89C450-ENL+ Level translator (20 TSSOP) U11 1 Maxim MAX3002EUP+ SUPPLIER AVX Corporation ...
Page 4
MAX19527 Evaluation Kit Recommended Equipment • MAX19527 EV kit • Single 3.3V power supply • Signal generator with low phase noise and low jitter for clock input (e.g., HP 8644B) • Signal generator for analog (e.g., HP 8644B) ...
Page 5
Table_1._Jumper_Configuration_(JU1–JU15) JUMPER SHUNT_POSITION Not installed JU1 Installed* Not installed JU2 Installed* Not installed JU3 Installed* Not installed JU4 Installed* Not installed JU5 Installed* Not installed JU6 Installed* Not installed JU7 Installed* Not installed JU8 Installed* 1-2 JU9 2-3* Not installed ...
Page 6
MAX19527 Evaluation Kit Detailed Description of Software Software Startup Before starting the MAX19527 EV kit software, verify that shunts are configured in their default states, as shown in Table 1 and a valid clock signal is applied at the EV ...
Page 7
Input/Output/Clock Tab The Output_ Format group box contains several func- tions that format the output data. The Reverse_ Bit_ Order checkbox allows the user to change the LVDS output data to a MSB-first format and displays the bit-order configuration. The ...
Page 8
MAX19527 Evaluation Kit Refer to the System Timing Requirements section in the MAX19527 IC data sheet for additional information for configuring the Data, FRAME, and CLKOUT test levels. Power Management Tab Power Management Controls The Power_ Management group box contains ...
Page 9
Figure 3. Advanced User Interface Window (3-Wire Interface Tab)—Writing to a Register Figure 4. Advanced User Interface Window (3-Wire Interface Tab)—Reading a Register ________________________________________________________________________________________ _ 9 MAX19527 Evaluation Kit ...
Page 10
MAX19527 Evaluation Kit Keyboard Navigation Press Ctrl + Tab to navigate to the tab sheets. The selected tab sheet is indicated by a dotted outline. Press the Tab key to select each GUI control. The selected control is indicated by ...
Page 11
Configuring the EV Kit for Single-Ended To configure the EV kit for single-ended clock operation, the following modifications must be made to the clock circuit: 1) Cut the traces at locations R99, R103, and R104. 2) Install 0I resistors at ...
Page 12
MAX19527 Evaluation Kit To maintain the ADC’s current register content, place shunts across pins 1-3 of JU11, JU12, and JU13. Shutdown (SHDN) The ADC can also be placed in a low-power shutdown mode through jumper JU9. The SHDN pin is ...
Page 13
Figure 5. Device Module DCEP GUI Window _______________________________________________________________________________________ _ 13 MAX19527 Evaluation Kit ...
Page 14
MAX19527 Evaluation Kit Figure 6a. MAX19527 EV Kit Schematic (Sheet 14_ _ ______________________________________________________________________________________ ...
Page 15
Figure 6b. MAX19527 EV Kit Schematic (Sheet _______________________________________________________________________________________ _ 15 MAX19527 Evaluation Kit ...
Page 16
MAX19527 Evaluation Kit Figure 6c. MAX19527 EV Kit Schematic (Sheet 16_ _ ______________________________________________________________________________________ ...
Page 17
Figure 6d. MAX19527 EV Kit Schematic (Sheet _______________________________________________________________________________________ _ 17 MAX19527 Evaluation Kit ...
Page 18
MAX19527 Evaluation Kit 1.0” Figure 7. MAX19527 EV Kit Component Placement Guide—Component Side 18_ _ ______________________________________________________________________________________ ...
Page 19
Figure 8. MAX19527 EV Kit PCB Layout—Component Side _______________________________________________________________________________________ _ 19 MAX19527 Evaluation Kit ...
Page 20
MAX19527 Evaluation Kit 1.0” Figure 9. MAX19527 EV Kit PCB Layout (Inner Layer 2)—Ground Planes 20_ _ ______________________________________________________________________________________ ...
Page 21
Figure 10. MAX19527 EV Kit PCB Layout (Inner Layer 3)—Power Planes _______________________________________________________________________________________ _ 21 MAX19527 Evaluation Kit ...
Page 22
MAX19527 Evaluation Kit 1.0” Figure 11. MAX19527 EV Kit PCB Layout (Inner Layer 4)—Ground Planes 22_ _ ______________________________________________________________________________________ ...
Page 23
Figure 12. MAX19527 EV Kit PCB Layout (Inner Layer 5)—Routing Plane _______________________________________________________________________________________ _ 23 MAX19527 Evaluation Kit ...
Page 24
MAX19527 Evaluation Kit 1.0” Figure 13. MAX19527 EV Kit PCB Layout—Solder Side 24_ _ ______________________________________________________________________________________ ...
Page 25
Figure 14. MAX19527 EV Kit PCB Component Placement Guide—Solder Side _______________________________________________________________________________________ _ 25 MAX19527 Evaluation Kit ...
Page 26
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ____________________ ________ Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 26_ 2010 Maxim Integrated Products © ...