ADV7303AKST Analog Devices Inc, ADV7303AKST Datasheet - Page 33

• Manufacturer Part Number: ADV7303AKST
• Description: IC DAC VIDEO HDTV 6-11BIT 64LQFP
• Manufacturer: Analog Devices Inc
• Type: Video Encoderr

Specifications of ADV7303AKST

• Rohs Status: RoHS non-compliant
• Applications: DVD, Set-Top Boxes
• Voltage - Supply, Analog: 2.37 V ~ 2.63 V
• Voltage - Supply, Digital: 2.37 V ~ 3.6 V
• Mounting Type: Surface Mount
• Package / Case: 64-LQFP
• Number Of Dac's: 6
• Adc/dac Resolution: 11b
• Screening Level: Commercial
• Package Type: LQFP
• Pin Count: 64
• Lead Free Status / RoHS Status: Compliant

TIMING MODES
HD Async Timing Mode
[Subaddress 10h, Bits 3–2]
For any input data that does not conform to SMPTE293M,
SMPTE274M, SMPTE296M, or ITU-R.BT1358 standards,
an Asynchronous Timing Mode can be used to interface to the
ADV7302A/ADV7303A. Timing control signals for HSYNC,
VSYNC, and BLANK have to be programmed by the user.
Macrovision is not available in Async Timing Mode.
Figure 28 shows an example of how to program the ADV7302A/
ADV7303A to accept a different high definition standard other
than SMPTE293M, SMPTE274M, SMPTE296M, or
ITU-R.BT1358 standards.
Table XIV must be followed when programming the control sig-
nals in Async Timing Mode.
HD Timing Reset
A timing reset is achieved in setting the HD Timing Reset Con-
trol Bit at Address 14h from “0” to “1.” In this state, the
horizontal and vertical counters will remain reset. On setting
this bit back to “0,” the internal counters will again commence
counting. The minimum time the pin has to be held high is one
clock cycle; otherwise, this reset signal might not be recognized.
This timing reset applies to the HD timing counters only.
SD Timing
Real-time Control, Subcarrier Reset, Timing Reset
[Subaddress 44h, Bits 2–1]
Together with the RTC_SCR_TR Pin and SD Mode Register 3
[Address 44h, Bits 1–2] the ADV7302A/ADV7303A can be
used in Timing Reset Mode, Subcarrier Phase Reset Mode,
or RTC Mode.
REV. A
P_BLANK*
*SET ADDRESS 10h, BIT 6 TO “1”
P_HSYNC
P_VSYNC
CLK
Figure 28. Async Timing Mode, Programming Input Control Signals for SMPTE295M Compatibility
81
a
HORIZONTAL SYNC
66
b
66
c
243
–33–
a. A timing reset is achieved in a low-to-high transition on the
b. Subcarrier phase reset, a low-to-high transition on the
c. In RTC Mode, the ADV7302A/ADV7303A can be used to
RTC_SCR_TR Pin (Pin 31). In this state, the horizontal and
vertical counters will remain reset. On releasing this pin (set
to low), the internal counters will again commence counting.
The minimum time the pin has to be held high is one clock
cycle; otherwise, this reset signal might not be recognized. This
timing reset applies to the SD timing counters only.
RTC_SCR_TR pin (Pin 31), will reset the subcarrier phase
to zero when the SD RTC/TR/SCR control bits at Address 44h
are set to “01.” This reset signal will have to be held high for
a minimum of one clock cycle. Since the Field Counter is
not reset, it is recommended to apply the reset in Field 7
(PAL). The reset of the phase will then occur on the next field
by being correctly lined up with the internal counters. The
Field Count Register at Address 7Bh can be used to identify
the number of the active field.
lock to an external video source. The Real-time Control Mode
allows the ADV7302A/ADV7303A to automatically alter the
subcarrier frequency to compensate for line length variations.
When the part is connected to a device that outputs a digital
data stream in the RTC format (such as a ADV7185 video
decoder, see Figure 29), the part will automatically change to
the compensated subcarrier frequency on a line-by-line basis.
This digital data stream is 67 bits wide and the subcarrier is
contained in Bits 0 to 21. Each bit is two clock cycles long.
00h should be written into all four Subcarrier Frequency
Registers when using this mode.
d
ACTIVE VIDEO
1920
ADV7302A/ADV7303A
e
PROGRAMMABLE
INPUT TIMING
ANALOG
OUTPUT