PCA9501BS,118 NXP Semiconductors, PCA9501BS,118 Datasheet - Page 22

• Manufacturer Part Number: PCA9501BS,118
• Description: IC I/O EXPANDER I2C 8B 20HVQFN
• Manufacturer: NXP Semiconductors

Specifications of PCA9501BS,118

• Package / Case: 20-VQFN Exposed Pad, 20-HVQFN, 20-SQFN, 20-DHVQFN
• Interface: I²C, SMBus
• Number Of I /o: 8
• Interrupt Output: Yes
• Frequency - Clock: 400kHz
• Voltage - Supply: 2.5 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Includes: EEPROM
• Logic Family: PCA9501
• Number Of Lines (input / Output): 8.0 / 8.0
• Operating Supply Voltage: 2.5 V to 3.6 V
• Power Dissipation: 400 mW
• Operating Temperature Range: - 40 C to + 85 C
• Input Voltage: 5 V
• Logic Type: I/O Expander
• Maximum Clock Frequency: 400 KHz
• Mounting Style: SMD/SMT
• Number Of Input Lines: 8.0
• Number Of Output Lines: 8.0
• Output Current: 25 mA
• Output Voltage: 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: OM6285 - EVAL BOARD I2C-2002-1A568-4002 - DEMO BOARD I2C
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-3352-2; 935273813118; PCA9501BS-T

NXP Semiconductors
14. Soldering of SMD packages
PCA9501_4
Product data sheet
14.1 Introduction to soldering
14.2 Wave and reflow soldering
14.3 Wave soldering
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description” .
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
Key characteristics in wave soldering are:
•
•
•
•
•
•
•
•
•
•
Through-hole components
Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Board specifications, including the board finish, solder masks and vias
Package footprints, including solder thieves and orientation
The moisture sensitivity level of the packages
Package placement
Inspection and repair
Lead-free soldering versus SnPb soldering
Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
Solder bath specifications, including temperature and impurities
Rev. 04 — 10 February 2009
8-bit I
2
C-bus and SMBus I/O port with interrupt, 2-kbit EEPROM
PCA9501
© NXP B.V. 2009. All rights reserved.
22 of 28