AD9821KSTZ Analog Devices Inc, AD9821KSTZ Datasheet - Page 6

• Manufacturer Part Number: AD9821KSTZ
• Description: IC IMAGE SGNL PROC 12BIT 48-LQFP
• Manufacturer: Analog Devices Inc
• Type: Image Sensorr

Specifications of AD9821KSTZ

• Input Type: Logic
• Output Type: Logic
• Interface: 3-Wire Serial
• Mounting Type: Surface Mount
• Package / Case: 48-LQFP
• Analog Front End Type: CCD
• Analog Front End Category: Video
• Interface Type: Serial (3-Wire)
• Sample Rate: 40MSPS
• Input Voltage Range: 0.5V
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Resolution: 12b
• Number Of Adc's: 1
• Power Supply Type: Analog/Digital
• Operating Temp Range: -20C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Number Of Channels: 1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant

AD9821
DEFINITIONS OF SPECIFICATIONS
Differential Nonlinearity (DNL)
An ideal ADC exhibits code transitions that are exactly 1 LSB
apart. DNL is the deviation from this ideal value. Thus, every
code must have a finite width. No missing codes guaranteed to
12-bit resolution indicates that all 4096 codes, respectively,
must be present over all operating conditions.
Peak Nonlinearity
Peak nonlinearity, a full signal chain specification, refers to the
peak deviation of the output of the AD9821 from a true straight
line. The point used as “zero scale” occurs 1/2 LSB before the
first code transition. “Positive full scale” is defined as a Level 1,
1/2 LSB beyond the last code transition. The deviation is mea-
sured from the middle of each particular output code to the true
straight line. The error is then expressed as a percentage of the
2 V ADC full-scale signal. The input signal is always appropriately
gained up to fill the ADC’s full-scale range.
EQUIVALENT INPUT CIRCUITS
Figure 1. Digital Inputs— DATACLK, CLPOB, PBLK, SCK, SL
THREE-
STATE
DATA
Figure 2. Data Outputs—D0–D11
330
DVDD
DVSS
DVDD
DVSS
DRVDD
DRVSS
DOUT
–6–
Total Output Noise
The rms output noise is measured using histogram techniques.
The standard deviation of the ADC output codes is calculated
in LSB and represents the rms noise level of the total signal
chain at the specified gain setting. The output noise can be
converted to an equivalent voltage using the relationship 1 LSB =
(ADC Full Scale/2
For the AD9821, 1 LSB is 500 µV.
Power Supply Rejection (PSR)
The PSR is measured with a step change applied to the supply
pins. This represents a very high frequency disturbance on the
AD9821’s power supply. The PSR specification is calculated
from the change in the data outputs for a given step change in
the supply voltage.
Internal Delay for SHA
The internal delay (also called aperture delay) is the time delay
that occurs from when the sampling edge is applied to the AD9821
until the actual sample of the input signal is held. The DATACLK
samples the input signal during the transition from low to high,
so the internal delay is measured from each clock’s rising edge
to the instant the actual internal sample is taken.
RNW
Figure 3. VIN+ and VIN– (Pins 30 and 31)
N
Figure 4. SDATA (Pin 47)
codes) when N is the bit resolution of the ADC.
DVSS
DVDD
ACVSS
AVDD
DATA OUT
DATA IN
60
DVSS
ACVSS
330
DVDD
DVSS
REV. 0