BLKD815EPFVU Intel, BLKD815EPFVU Datasheet
BLKD815EPFVU
Specifications of BLKD815EPFVU
BLKD815EPFVU Summary of contents
Page 1
... The Intel Desktop Boards D815EFV and D815EPFV may contain design defects or errors known as errata that may cause the product to deviate from published specifications. Current characterized errata are documented in the Intel Desktop Board D815EFV/D815EPFV Specification Update. Desktop Board ® May 2001 ...
Page 2
... Intel products are not intended for use in medical, life saving, or life sustaining applications or for any other application in which the failure of the Intel product could create a situation where personal injury or death may occur. ...
Page 3
... Preface This Technical Product Specification (TPS) specifies the board layout, components, connectors, power and environmental requirements, and the BIOS for these Intel Desktop Boards: D815EFV and D815EPFV. It describes the standard product and available manufacturing options. Intended Audience The TPS is intended to provide detailed, technical information about the D815EFV and D815EPFV boards and their components to the vendors, system integrators, and other engineers and technicians who need this level of information ...
Page 4
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification Other Common Notation # Used after a signal name to identify an active-low signal (such as USBP0#) (NxnX) When used in the description of a component, N indicates component type, xn are the relative coordinates of its location on the D815EFV and D815EPFV boards, and X is the instance of the particular part at that general location ...
Page 5
... Serial Ports ..................................................................................................35 1.9.2 Parallel Port..................................................................................................36 1.9.3 Diskette Drive Controller ..............................................................................36 1.9.4 Keyboard and Mouse Interface ....................................................................36 1.10 Graphics Subsystems.................................................................................................37 1.10.1 Intel 815E Graphics Subsystem ...................................................................37 1.10.2 Intel 815EP Graphics Subsystem.................................................................41 1.11 Audio Subsystem........................................................................................................42 1.11.1 AD1885 Audio Codec...................................................................................42 1.11.2 Audio Connectors.........................................................................................42 1.12 LAN Subsystem (Optional) .........................................................................................44 ® ...
Page 6
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 2.3 I/O Map ......................................................................................................................58 2.4 DMA Channels ...........................................................................................................60 2.5 PCI Configuration Space Map ....................................................................................60 2.6 Interrupts ....................................................................................................................61 2.7 PCI Interrupt Routing Map ..........................................................................................61 2.8 Connectors .................................................................................................................63 2.8.1 Back Panel Connectors................................................................................64 2.8.2 Internal I/O Connectors ................................................................................68 2.8.3 External I/O Connectors ...............................................................................78 2.9 Jumper Blocks............................................................................................................82 2 ...
Page 7
... Location of Universal Board Designator .........................................................................12 2. Board Components ........................................................................................................15 3. Block Diagram for the D815EFV Board ..........................................................................16 4. Block Diagram for the D815EPFV Board........................................................................17 5. Intel 815E Chipset Block Diagram ..................................................................................25 6. USB Port Configurations ................................................................................................28 7. Intel 815EP Chipset Block Diagram................................................................................30 8. USB Port Configurations ................................................................................................33 9. Block Diagram of Audio Subsystem ...............................................................................42 ® ...
Page 8
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 10. ICH2 and CNR Signal Interface....................................................................................46 11. Using the Wake on LAN Technology Connector...........................................................53 12. Location of Standby Power Indicator LED ....................................................................54 13. Back Panel Connectors ................................................................................................64 14. Audio, Video, Power, and Hardware Control Connectors .............................................69 15. Add-in Board and Peripheral Interface Connectors ......................................................73 16 ...
Page 9
Audio Line Out Connector ..........................................................................................67 28. Audio Line In Connector .............................................................................................67 29. Auxiliary Line In Connector (J6B4) .............................................................................70 30. Front Panel Audio Connector (J6B2) (Optional)..........................................................70 31. ATAPI CD-ROM Connector (J6B3).............................................................................70 32. Digital Video Out Connector (J5C1) (Optional; present only ...
Page 10
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 74. Video Configuration Submenu ..................................................................................125 75. Security Menu ..........................................................................................................126 76. Power Menu .............................................................................................................127 77. APM Submenu .........................................................................................................128 78. ACPI Submenu.........................................................................................................129 79. Boot Menu ................................................................................................................130 80. Boot Device Priority Submenu ..................................................................................131 81. Hard Disk Drives Submenu ......................................................................................132 82. Removeable Devices Submenu................................................................................132 83. ...
Page 11
... D815EPFV Controller Hub (MCH) • Provides this video feature: AGP universal connector ® Desktop boards: D815EFV and D815EPFV. Table 1 summarizes ® 815E Chipset, which includes the Intel ® 815EP Chipset, which includes the Intel ® 82815 Graphics and ® 82815EP Memory ...
Page 12
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 1.1.2 Identifying Universal Boards The Universal versions of the D815EFV and D815EPFV can be identified by an uppercase “U” on the silkscreen of the board. Figure 1 shows the location of the Universal board designator. Figure 1. Location of Universal Board Designator ✏ ...
Page 13
... Three PCI bus add-in card connectors (SMBus routed to PCI bus connector 2) Expansion Capabilities • One AGP universal connector • Intel/AMI BIOS (stored in an STM M50FW040 4 Mbit FWH or equivalent) BIOS • Support for Advanced Power Management (APM), Advanced Configuration and Power Interface (ACPI), Plug and Play, and SMBIOS ® ...
Page 14
... The board’s compliance level with APM, ACPI, Plug and Play, and SMBIOS 1.2.2 Manufacturing Options Table 3 describes the D815EFV and D815EPFV boards’ manufacturing options. Not every manufacturing option is available in all marketing channels. Please contact your Intel representative to determine which manufacturing options are available to you. Table 3. ...
Page 15
... Communication and Networking Riser (CNR) connector (optional) B AD1885 audio codec C AGP universal connector D Back panel connectors E DVO connector (optional) • Intel 82815 Graphics and Memory Controller F Hub (GMCH) (D815EFV boards) • Intel 82815EP Memory Controller Hub (MCH) (D815EPFV boards) G Processor socket H DIMM sockets I ...
Page 16
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 1.2.4 Block Diagrams Figure block diagram of the major functional areas of the D815EFV board. Primary/ Secondary IDE Processor Socket System Bus 82815 SDRAM Bus Graphics and Memory Controller DIMM Hub (GMCH) Banks (3) DVO Digital Video ...
Page 17
Figure block diagram of the major functional areas of the D815EPFV board. Primary/ Secondary IDE Processor Socket System Bus SDRAM Bus 82815EP Memory Controller Hub (MCH) DIMM Banks (3) AGP Universal AGP Bus Connector PCI Bus PCI ...
Page 18
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 1.3 Online Support To find information about… Intel’s D815EFV and D815EPFV boards under “Product Info” or “Customer Support” Processor data sheets ICH2 addressing Custom splash screens Audio software and utilities LAN software and drivers 1 ...
Page 19
... Intel Corporation. 298177.htm AMIBIOS 99, http://www.amij.com/amibios/ 1999, bios.platforms.desktop.html American Megatrends, Inc. Version 1.2, http://www.microsoft.com/ February 1996, hwdev/busbios/amp_12.htm Intel Corporation and Microsoft Corporation. Revision 3, http://www.t13.org February 29, 2000, Contact: T13 Chair, Seagate Technology. Version 2.03, http://www.formfactors.org/ December 1998, developer/specs/atx/ Intel Corporation. ...
Page 20
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification Table 4. Specifications (continued) Reference Specification Name Title DVI Digital Visual Interface DVI EPP IEEE Std 1284.1-1997 (Enhanced Parallel Port) El Torito Bootable CD-ROM Format Specification GPA (see AIMM) LPC Low Pin Count Interface Specification MicroATX ...
Page 21
... Interface Design Guide USB Universal Serial Bus Specification WfM Wired for Management Baseline Version, Revision Date and Ownership Revision 1.0, February 1998, Intel Corporation. Revision 1.7, November 1999, Intel Corporation. Revision 1.2B, November 1999, Intel Corporation. Version 2.3.1, March 16, 1999, American Megatrends Incorporated, ...
Page 22
... Processor CAUTION Use only the processors listed below. Use of unsupported processors can damage the board, the processor, and the power supply. See the Intel Update for the most up-to-date list of supported processors for the D815EFV and D815EPFV boards. The D815EFV and D815EPFV boards both support a single Pentium III or Celeron processor. The system bus frequency is automatically selected ...
Page 23
... NOTE To be fully compliant with all applicable Intel be populated with DIMMs that support the Serial Presence Detect (SPD) data structure. This allows the BIOS to read the SPD data and program the chipset to accurately configure memory settings for optimum performance. If non-SPD memory is installed, the BIOS will attempt to ...
Page 24
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification ✏ NOTE If more than four rows of 133 MHz SDRAM are populated, the BIOS will display a message indicating that it will initialize installed memory up to 512 MB at 100 MHz. For information about Obtaining the PC Serial Presence Detect (SPD) Specification Table 6 lists the supported DIMM configurations ...
Page 25
... This section describes the chipsets used by the D815EFV and D815EPFV boards: • The D815EFV board uses the Intel 815E Chipset, described below. • The D815EPFV board uses the Intel 815EP Chipset, described in Section 1.8.2, beginning on page 30. ® 1.8.1 Intel 815E Chipset The Intel 815E chipset consists of the following devices: • ...
Page 26
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification ® 1.8.1.1 Intel 82815 Graphics and Memory Controller Hub (GMCH) The GMCH provides the following: • An integrated Synchronous DRAM memory controller with autodetection of SDRAM • An interface for a single AGP device or a Graphics Performance Accelerator (GPA) card • ...
Page 27
NOTE ATA-66 and ATA-100 are faster timings and require a specialized cable to reduce reflections, noise, and inductive coupling. The IDE interfaces also support ATAPI devices (such as CD-ROM drives) and ATA devices using the transfer modes listed in ...
Page 28
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification Standard Configuration 82801BA I/O Controller Hub (ICH2) 82801BA I/O Controller Hub (ICH2) USB SMSC LPC47M142 LPC Bus I/O Controller ✏ NOTE Computer systems that have an unshielded cable attached to a USB port may not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable ...
Page 29
Real-Time Clock, CMOS SRAM, and Battery The real-time clock provides a time-of-day clock and a multicentury calendar with alarm features. The real-time clock supports 256 bytes of battery-backed CMOS SRAM in two banks that are reserved for BIOS use. ...
Page 30
... The MCH is a centralized controller for the system bus, the memory bus, the AGP bus, and the AHA bus. The ICH2 is a centralized controller for the board’s I/O paths. The FWH provides the nonvolatile storage of the BIOS. The Intel 815EP chipset provides the interfaces shown in Figure 7. System Bus SDRAM Bus ...
Page 31
... An interface for a single AGP device • Support for ACPI Rev. 2.0 and APM Rev. 1.2 compliant power management 1.8.2.2 Intel 82801BA I/O Controller Hub (ICH2) The ICH2 provides the following: • 33 MHz PCI bus interface • Support for up to four PCI master devices • ...
Page 32
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification The IDE interfaces also support ATAPI devices (such as CD-ROM drives) and ATA devices using the transfer modes listed in Table 71 on page 121. The BIOS supports Logical Block Addressing (LBA) and Extended Cylinder Head Sector (ECHS) translation modes ...
Page 33
Standard Configuration 82801BA I/O Controller Hub (ICH2) 82801BA I/O Controller Hub (ICH2) USB SMSC LPC47M142 LPC Bus I/O Controller ✏ NOTE Computer systems that have an unshielded cable attached to a USB port may not meet FCC Class B requirements, ...
Page 34
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 1.8.2.2.3 Real-Time Clock, CMOS SRAM, and Battery The real-time clock provides a time-of-day clock and a multicentury calendar with alarm features. The real-time clock supports 256 bytes of battery-backed CMOS SRAM in two banks that are reserved for BIOS use. ...
Page 35
... Serial IRQ interface compatible with serialized IRQ support for PCI systems • PS/2-style mouse and keyboard interfaces • Interface for one 1.2 MB, 1.44 MB, or 2.88 MB diskette drive • Intelligent power management, including a programmable wake up event interface • PCI power management support • Fan control One fan control output ...
Page 36
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 1.9.2 Parallel Port The connector for the parallel port is a 25-pin D-Sub connector located on the back panel. In the BIOS Setup program, the parallel port can be set to the following modes: • † Output only (PC-AT -compatible mode) • ...
Page 37
... The D815EFV board uses the Intel 815E graphics subsystem, described below. • The D815EPFV board uses the Intel 815EP graphics subsystem, described in Section 1.10.2, beginning on page 41. 1.10.1 Intel 815E Graphics Subsystem The 815E chipset, used on the D815EFV board, contains two separate, mutually exclusive graphics options ...
Page 38
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification Table 7 lists the refresh frequencies supported by the graphics subsystem. Table 7. Supported Graphics Refresh Frequencies Resolution Color Palette 256 colors 320 x 200 64 K colors 16 M colors 256 colors 320 x 240 64 K colors 16 M colors 256 colors ...
Page 39
... Digital Video Output (DVO) Connector (Optional) The D815EFV board routes the Intel 82815 GMCH DVO port to an optional onboard 40-pin DVO connector. The DVO connector can be cabled to a DVI or TV out card to enable digital displays or TV out functionality. The Digital Visual Interface (DVI) specification provides a high-speed digital connection for visual data types when using the integrated graphics controller ...
Page 40
... Graphics Performance Accelerator (GPA) Support The Intel 815E GMCH display cache is a single channel 32-bit wide SDRAM interface. The 4 MB display cache resides on a GPA card that plugs into the AGP connector. The BIOS detects a GPA card if present in the AGP port and initializes it as display cache memory. When a GPA card is initialized, the BIOS allocates system memory to support the internal display device operation ...
Page 41
... Install memory in the DIMM sockets prior to installing the AGP video card to avoid interference with the memory retention mechanism. The Intel 815EP chipset, used on the D815EPFV board, provides an AGP universal connector which supports a 1x, 2x AGP add-in card with either 3 1.5 V I/O. AGP is a high-performance interface for graphics-intensive applications, such as 3D applications. ...
Page 42
... Full-duplex operation at asynchronous hardware record/playback samples rates • Frequency response kHz (± 0.1 dB) Figure block diagram of the D815EFV and D815EPFV boards’ audio subsystem, including the Intel 82801BA ICH2 digital controller, the AD1885 analog codec, and the audio connectors. 82801BA I/O Controller Hub (ICH2) Figure 9 ...
Page 43
Back panel audio connectors: Line in Line out Mic in For information about The back panel audio connectors 1.11.2.1 Front Panel Audio Connector (Optional 5-pin connector for routing mic in and line out ...
Page 44
... Obtaining LAN software and drivers ® 1.12.1 Intel 82562ET Platform LAN Connect Device The Intel 82562ET component provides an interface to the back panel RJ-45 connector with integrated LEDs. This physical interface may alternately be provided through the CNR connector. The Intel 82562ET provides the following functions: • ...
Page 45
Hardware Management Subsystem The hardware management features enable the board to be compatible with the Wired for Management (WfM) specification. The board has several hardware management features, including the following: • Hardware monitoring • Chassis intrusion detect connector (optional) ...
Page 46
... The signal names of the fan connectors 1.14 CNR Connector (Optional) The CNR connector supports the audio, modem, USB, and LAN interfaces of the Intel 815E and Intel 815EP chipsets. Figure 10 shows the signal interface between the riser and the ICH2. Intel 82801BA ...
Page 47
Power Management Power management is implemented at several levels, including: • Software support: Advanced Power Management (APM) Advanced Configuration and Power Interface (ACPI) • Hardware support: Power connector Fan connectors Wake on LAN technology ...
Page 48
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification The BIOS enables APM by default; but the operating system must support an APM driver for the power management features to work. For example, Windows 98 supports the power management features upon detecting that APM is enabled in the BIOS. ...
Page 49
System States and Power States Under ACPI, the operating system directs all system and device power state transitions. The operating system puts devices in and out of low-power states based on user preferences and knowledge of how devices are ...
Page 50
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 1.15.1.2.2 Wake Up Devices and Events Table 11 lists the devices or specific events that can wake the computer from specific states. Table 11. Wake Up Devices and Events These devices/events can wake up the computer… Power switch RTC alarm ...
Page 51
Hardware Support CAUTION If the Wake on LAN and Instantly Available technology features are used, ensure that the power supply provides adequate +5 V standby current. Failure can damage the power supply. The total amount of ...
Page 52
... NOTE The optional Wake on LAN technology connector is present only on boards that do not have the Intel 82562ET PLC device, which is part of the optional onboard LAN subsystem. Wake on LAN technology enables remote wakeup of the computer through a network. The LAN subsystem PCI bus network adapter monitors network traffic at the Media Independent Interface. ...
Page 53
The Wake on LAN technology connector can be used with PCI bus network adapters that have a remote wake up connector, as shown in Figure 11. Network adapters that are PCI 2.2 compliant assert the wakeup signal through the PCI ...
Page 54
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification Present only on D815EFV boards Figure 12. Location of Standby Power Indicator LED For information about The devices and events that can wake the computer from the S3 state The PCI Bus Power Management Interface Specification 1.15.2.5 Resume on Ring The operation of Resume on Ring can be summarized as follows: • ...
Page 55
Wake from USB USB bus activity wakes the computer from an ACPI state. ✏ NOTE Wake from USB requires the use of a USB peripheral that supports Wake from USB. 1.15.2.7 Wake from PS/2 Keyboard PS/2 ...
Page 56
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 56 ...
Page 57
Technical Reference What This Chapter Contains 2.1 Introduction.................................................................................................................57 2.2 Memory Map ..............................................................................................................57 2.3 I/O Map .....................................................................................................................58 2.4 DMA Channels ...........................................................................................................60 2.5 PCI Configuration Space Map ....................................................................................60 2.6 Interrupts ....................................................................................................................61 2.7 PCI Interrupt Routing Map ..........................................................................................61 2.8 Connectors .................................................................................................................63 2.9 ...
Page 58
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 2.3 I/O Map Table 14. I/O Map Address (hex) Size 0000 - 000F 16 bytes 0020 - 0021 2 bytes 0040 - 0043 4 bytes 0060 1 byte 0061 1 byte 0064 1 byte 0070 - 0071 2 bytes 0072 - 0073 2 bytes 0080 - 008F 16 bytes 0092 ...
Page 59
... Secondary bus master IDE registers ICH2 (ACPI + TCO) D815EFV/D815EPFV board resource ICH2 LAN controller ICH2 AC ’97 audio master ICH2 AC ’97 audio mixer ICH2 AC ’97 modem mixer ICH2 USB controller #1 ICH2 USB controller #2 ICH2 (SMBus) Intel 82801BA PCI bridge Refer to Section 1.3, page 18 Technical Reference 59 ...
Page 60
... Memory controller of Intel 82815 component 00 PCI to AGP bridge 00 Intel 82815 GMCH (graphics memory controller hub)/ Intel 82815EP MCH (memory controller hub) 00 Hub link to PCI bridge 00 Intel 82801BA ICH2 PCI to LPC bridge 01 IDE controller 02 ICH2 USB controller #1 03 SMBus controller 04 ICH2 USB controller # ’ ...
Page 61
Interrupts Table 17. Interrupts IRQ System Resource NMI I/O channel check 0 Reserved, interval timer 1 Reserved, keyboard buffer full 2 Reserved, cascade interrupt from slave PIC (Note) 3 COM2 (Note) 4 COM1 5 LPT2 (Plug and Play option)/Audio/User ...
Page 62
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification The ICH2 has eight programmable interrupt request (PIRQ) input signals. All PCI interrupt sources either onboard or from a PCI add-in card connect to one of these PIRQ signals. Some PCI interrupt sources are electrically tied together on the D815EFV and D815EPFV boards and therefore share the same interrupt ...
Page 63
Connectors CAUTION Only the back panel connectors of the D815EFV and D815EPFV boards have overcurrent protection. The D815EFV and D815EPFV boards’ internal connectors are not overcurrent protected and should connect only to devices inside the computer’s chassis, such as ...
Page 64
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 2.8.1 Back Panel Connectors Figure 13 shows the location of the back panel connectors on the D815EFV and D815EPFV boards. The back panel connectors are color-coded in compliance with PC 99 recommendations. The figure legend below lists the colors used. ...
Page 65
NOTE The back panel audio line out connector is designed to power headphones or amplified speakers only. Poor audio quality occurs if passive (non-amplified) speakers are connected to this output. Table 19 lists the overcurrent protection for the D815EFV ...
Page 66
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification Table 23. Parallel Port Connector Pin Standard Signal Name 1 STROBE# 2 PD0 3 PD1 4 PD2 5 PD3 6 PD4 7 PD5 8 PD6 9 PD7 10 ACK# 11 BUSY 12 PERROR 13 SELECT 14 AUDOFD# 15 FAULT# 16 INIT# 17 SLCTIN Ground Table 24. Serial Port A Connector Pin Signal Name 1 DCD (Data Carrier Detect) ...
Page 67
Table 25. LAN Connector (Optional) Pin Signal Name 1 TX+ 2 TX- 3 RX+ 4 Ground 5 Ground 6 RX- 7 Ground 8 Ground Table 26. Mic In Connector Pin Signal Name Tip Mono in Ring Mic bias voltage Sleeve ...
Page 68
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 2.8.2 Internal I/O Connectors The internal I/O connectors are divided into the following functional groups: • Audio, video, power, and hardware control (see page 69) Front panel audio (optional) ATAPI CD-ROM Auxiliary line in ...
Page 69
Audio, Video, Power, and Hardware Control Connectors Figure 14 shows the location of the audio, video, power, and hardware control connectors on the D815EFV and D815EPFV boards Present only on D815EFV boards Item ...
Page 70
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification Table 29. Auxiliary Line In Connector (J6B4) Pin Signal Name 1 Left auxiliary line in 2 Ground 3 Ground 4 Right auxiliary line in Table 30. Front Panel Audio Connector (J6B2) (Optional) Pin Signal Name 1 MICIN_FP 3 MIC_BIAS 5 AUD_FPOUT_R 7 Reserved 9 AUD_FPOUT_L ✏ NOTE The front panel audio connector is alternately used as a jumper block for routing audio signals ...
Page 71
Table 32. Digital Video Out Connector (J5C1) (Optional; present only on D815EFV boards) Pin Signal Name 1 LTVCLKIN 3 P_RST_SLOTS# 5 Ground 7 Ground 9 Ground 11 Ground 13 Ground 15 Ground 17 Ground 19 Ground 21 Ground 23 Ground ...
Page 72
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification Table 35. Chassis Fan Connector (J4G1) (Optional) Pin Signal Name 1 FAN3_PWM 2 + connect Table 36. System Fan Connector (J9H1) Pin Signal Name 1 FAN2_PWM 2 + FAN2_TACH Table 37. Chassis Intrusion Connector (J9H3) (Optional) Pin Signal Name 1 INTRUDER# 2 Ground Table 38. ...
Page 73
Add-in Board and Peripheral Interface Connectors Figure 15 shows the location of the add-in board connectors and peripheral interface connectors on the D815EFV and D815EPFV boards. Note the following considerations for the PCI bus connectors: • All of the ...
Page 74
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification Table 39. CNR Connector (J9B1) (Optional) Pin Signal Name A1 Reserved A2 Reserved A3 Ground A4 Reserved A5 Reserved A6 Ground A7 LAN_TXD2 A8 LAN_TXD0 A9 Ground A10 LAN_CLK A11 LAN_RXD1 A12 Reserved A13 USB+ (optional)* A14 Ground A15 USB- (optional)* A16 +12 V A17 ...
Page 75
Table 40. PCI Bus Connectors (J7B1, J8B2, and J9B2) Pin Signal Name Pin Signal Name A1 Ground (TRST#)* Ground (TCK (TMS)* B3 Ground (TDI)* B4 Not connected ...
Page 76
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification Table 41. AGP Universal Connector (J6C1) Pin Signal Name Pin A1 + TYPEDET Reserved B3 A4 Not connected B4 A5 Ground B5 A6 INTA RST GNT1 Vcc3.3 B9 A10 ST1 B10 A11 Reserved B11 A12 PIPE# B12 A13 Ground B13 A14 ...
Page 77
Table 42. Diskette Drive Connector (J6H2) Pin Signal Name 1 Ground 3 Ground 5 Key 7 Ground 9 Ground 11 Ground 13 Ground 15 Ground 17 Not connected 19 Ground 21 Ground 23 Ground 25 Ground 27 Not connected 29 ...
Page 78
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 2.8.3 External I/O Connectors Figure 16 shows the locations of the external I/O connectors on the D815EFV and D815EPFV boards Present only on D815EFV boards Item Description A Auxiliary front panel power LED B Front panel C SCSI LED D Serial port B ...
Page 79
Table 44. Serial Port B Connector (J8H1) Pin Signal Name 1 DCD2# 3 TXD2 (Transmit Data) 5 Ground 7 RTS2# 9 RI2# Table 45. Front Panel USB Connector (J8F1) (Optional) Pin Signal Name 1 VREG_FP_USB_PWR 3 ICH_FP0# 5 ICH_FP0 7 ...
Page 80
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 2.8.3.3 Front Panel Connector This section describes the functions of the front panel connector. Table 48 lists the signal names of the front panel connector. Table 48. Front Panel Connector (J9H3) Pin Signal In/Out 1 HD_PWR Out 3 HDA# Out ...
Page 81
Power/Sleep/Message Waiting LED Connector Pins 2 and 4 can be connected to a single-colored or dual-colored LED. Table 49 shows the possible states for a single-colored LED. Table 50 shows the possible states for a dual-colored LED. Table 49. ...
Page 82
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 2.9 Jumper Blocks CAUTION Do not move any jumpers with the power on. Always turn off the power and unplug the power cord from the computer before changing a jumper setting. Otherwise, the board could be damaged. Figure 17 shows the locations of the jumper blocks on the D815EFV and D815EPFV boards. ...
Page 83
CAUTION Do not place jumpers on this block in any configuration other than the one described in Table 51. Other jumper configurations are not supported and could damage the board. Table 51. Front Panel Audio Connector / Jumper Block (J6B2) ...
Page 84
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 2.10 Mechanical Considerations 2.10.1 Form Factor The D815EFV and D815EPFV boards are designed to fit into a standard microATX-form-factor chassis. Figure 18 illustrates the mechanical form factor for the D815EFV and D815EPFV boards. Dimensions are given in inches [millimeters]. The outer dimensions are 9.60 inches by 8 ...
Page 85
... ATX specification. For information about The ATX specification The microATX specification How to identify a Universal D815EFV / D815EPFV board ✏ NOTE An I/O shield compliant with the ATX chassis specification 2.03 is available from Intel. Technical Reference Refer to Table 4, page 18 Table 4, page 18 Section 1.1.2, page 12 85 ...
Page 86
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 0.039 Dia. [1.000] 0.884 [22.450] 0.276 [7.012] 0.00 0.465 [11.811] 0.567 [14.400] (for D815EFV Universal Boards with Onboard LAN Subsystem) 86 6.390 Ref [162.300] 0.787±0.010 TYP [20±0.254] 3x Dia 0.330 [8.380] 4x Dia 0.125 [3.180] Figure 19. I/O Shield Dimensions 0.063± ...
Page 87
TYP [20±0.254] 0.039 Dia. [1.000] 0.884 [22.450] 0.276 [7.012] 0.00 0.465 [11.811] 0.567 [14.400] Figure 20. I/O Shield Dimensions (for D815EPFV Universal Boards with Onboard LAN Subsystem) 6.390 Ref [162.300] 3x Dia 0.330 [8.380] 4x Dia 0.125 [3.180] Technical ...
Page 88
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 0.787±0.010 TYP [20±0.254] 0.039 Dia. [1.000] 0.884 [22.450] 0.276 [7.012] 0.00 0.465 [11.811] 0.567 [14.400] (for D815EPFV Universal Boards without Onboard LAN Subsystem) 88 6.390 Ref [162.300] 3x Dia 0.330 [8.380] 4x Dia 0.125 [3.180] Figure 21. I/O Shield Dimensions 0.063± ...
Page 89
TYP [20 3x Dia 0.039 [1.000] 0.884 [22.450] 0.276 [7.012] 0.000 [0.000] 0.465 [11.811] 0.567 [14.400] Figure 22. I/O Shield Dimensions (for D815EFV Boards with Onboard LAN Subsystem) 6.390 REF [162.300] 0.254] 3x Dia 0.330 [8.380] Technical Reference ...
Page 90
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 0.787 3x Dia 0.039 [1.000] 0.884 [22.450] 0.276 [7.012] 0.000 [0.000] 0.465 [11.811] 0.567 [14.400] (for D815EPFV Boards with Onboard LAN Subsystem) 90 6.390 REF [162.300] 0.010 TYP [20 0.254] 3x Dia 0.330 [8.380] Figure 23. I/O Shield Dimensions ...
Page 91
TYP [20 0.254] 3x Dia 0.039 [1.000] 0.884 [22.450] 0.276 [7.012] 0.000 [0.000] 0.465 [11.811] 0.567 [14.400] Figure 24. I/O Shield Dimensions (for D815EPFV Boards without Onboard LAN Subsystem) 6.390 REF [162.300] 3x Dia 0.330 [8.380] Pictorial Technical ...
Page 92
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 2.11 Electrical Considerations 2.11.1 Power Consumption Table 54 lists voltage and current measurements for a computer that contains the D815EFV board and the following: • 800 MHz Intel Pentium III processor with a 256 KB cache • 128 MB SDRAM • 3.5-inch diskette drive • ...
Page 93
Add-in Board Considerations The D815EFV and D815EPFV boards are designed to provide 2 A (average current for each add-in board. The total +5 V current draw for add-in boards in a fully-loaded D815EFV or D815EPFV board ...
Page 94
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification ✏ NOTE AGP and PCI requirements are calculated by totaling the following: • One wake-enabled device @ 375 mA • Three non-wake-enabled devices @ 20 mA each PS/2 Ports requirements per the IBM PS/2 Port Specification (Sept 1991): • ...
Page 95
... Figure 25 shows the locations of the localized high temperature zones for the D815EFV and D815EPFV boards. D Present only on D815EFV boards A Processor voltage regulator area • Intel 82815 Graphics and Memory Controller Hub (GMCH) B (D815EFV boards) • Intel 82815EP Memory Controller Hub (MCH) (D815EPFV boards) C ...
Page 96
... Intel 82815 GMCH/ Intel 82815EP MCH Intel 82801BA ICH2 For information about Intel Pentium III processor datasheets and specification updates Intel Celeron processor datasheets and specification updates 2.13 Reliability The mean time between failures (MTBF) prediction is calculated using component and subassembly random failure rates. The calculation is based on the Bellcore Reliability Prediction Procedure, TR-NWT-000332, Issue 4, September 1991 ...
Page 97
Environmental Table 57 lists the environmental specifications for the D815EFV and D815EPFV boards. Table 57. D815EFV and D815EPFV Board Environmental Specifications Parameter Specification Temperature -40 °C to +70 °C Non-Operating 0 °C to +55 °C Operating Shock Unpackaged 30 ...
Page 98
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 2.15 Regulatory Compliance This section describes the D815EFV and D815EPFV boards’ compliance with U.S. and international safety and electromagnetic compatibility (EMC) regulations. 2.15.1 Safety Regulations Table 58 lists the safety regulations the D815EFV and D815EPFV boards comply with when correctly installed in a compatible host system ...
Page 99
... The D815EFV and D815EPFV desktop boards have the following product certification markings: • UL joint US/Canada Recognized Component mark: Consists of lower case c followed by a stylized backward UR and followed by a small US. Includes adjacent UL file number for Intel desktop boards: E210882 (component side). • ...
Page 100
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 100 ...
Page 101
... BIOS Security Features............................................................................................109 3.1 Introduction The D815EFV and D815EPFV boards use an Intel/AMI BIOS that is stored in the Firmware Hub (FWH) and can be updated using a disk-based program. The FWH contains the BIOS Setup program, POST, APM, the PCI auto-configuration utility, and Plug and Play support. ...
Page 102
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 3.2 BIOS Flash Memory Organization The FWH (an STM M50FW040 or equivalent) includes a 4 Mbit (512 KB) symmetrical flash memory device. Internally, the device is grouped into eight 64-KB blocks that are individually erasable, lockable, and unlockable. 3.3 Resource Configuration 3 ...
Page 103
... The MIF database defines the data and provides the method for accessing this information. The BIOS enables applications such as Intel SMBIOS. The BIOS stores and reports the following SMBIOS information: • ...
Page 104
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 3.5 Legacy USB Support Legacy USB support enables USB devices such as keyboards, mice, and hubs to be used even when the operating system’s USB drivers are not yet available. Legacy USB support is used to access the BIOS Setup program, and to install an operating system that supports USB. By default, legacy USB support is set to Enabled ...
Page 105
... BIOS Updates The BIOS can be updated using either of the following utilities, which are available on the Intel World Wide Web site: • ® Intel Express BIOS Update utility, which enables automated updating while in the Windows environment. Using this utility, the BIOS can be updated from a file on a hard disk, a 1.44 MB diskette CD-ROM, or from the file location on the Web. • ...
Page 106
... A series of continuous beeps indicates a failed BIOS recovery. To create a BIOS recovery diskette, a bootable diskette must be created and the BIOS update files copied to it. BIOS upgrades and the Intel Flash Memory Upgrade utility are available from Intel Customer Support through the Intel World Wide Web site. ...
Page 107
... Selecting a compatible operating system The BIOS is not configured by default to boot at the fastest possible speed. Empirical measurements have shown that some Intel Desktop boards, when optimized as described above, can complete POST (Power-On Self-Test) in six seconds or less and boot to an active Microsoft Windows Me operating system in 21 seconds. ...
Page 108
... Make sure that Quiet Boot is disabled, to eliminate the logo splash screen. This could save several seconds of painting complex graphic images and changing video modes. • Make sure the Intel Rapid BIOS Boot option (in the Boot menu of the BIOS Setup Program) is enabled (this is typically the default setting). This feature bypasses memory count and floppy seek. ...
Page 109
BIOS Security Features The BIOS includes security features that restrict access to the BIOS Setup program and who can boot the computer. A supervisor password and a user password can be set for the BIOS Setup program and for ...
Page 110
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 110 ...
Page 111
BIOS Setup Program What This Chapter Contains 4.1 Introduction...............................................................................................................111 4.2 Maintenance Menu ...................................................................................................112 4.3 Main Menu................................................................................................................114 4.4 Advanced Menu........................................................................................................115 4.5 Security Menu ..........................................................................................................126 4.6 Power Menu .............................................................................................................127 4.7 Boot Menu ................................................................................................................130 4.8 Exit Menu .................................................................................................................133 4.1 Introduction The BIOS ...
Page 112
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification Table 62 lists the function keys available for menu screens. Table 62. BIOS Setup Program Function Keys BIOS Setup Program Function Key <←> or <→> <↑> or <↓> <Tab> <Enter> <F9> <F10> <Esc> 4.2 Maintenance Menu To access this menu, select Maintenance on the menu bar at the top of the screen ...
Page 113
Extended Configuration Submenu To access this submenu, select Maintenance on the menu bar, then Extended Configuration. Main Maintenance Extended Configuration The submenu represented by Table 64 is for setting video memory cache mode. This submenu becomes available when User ...
Page 114
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 4.3 Main Menu To access this menu, select Main on the menu bar at the top of the screen. Maintenance Main Table 65 describes the Main Menu. This menu reports processor and memory information and is for configuring the system date and system time. ...
Page 115
Advanced Menu To access this menu, select Advanced on the menu bar at the top of the screen. Maintenance Main Table 66 describes the Advanced Menu. This menu is used for setting advanced features that are available through the ...
Page 116
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 4.4.1 PCI Configuration Submenu To access this submenu, select Advanced on the menu bar, then PCI Configuration. Maintenance Main The submenu represented by Table 67 is for configuring the IRQ priority of PCI slots individually. Table 67. PCI Configuration Submenu ...
Page 117
Boot Configuration Submenu To access this submenu, select Advanced on the menu bar, then Boot Configuration. Maintenance Main The submenu represented by Table 68 is for setting Plug and Play options, resetting configuration data, and the power-on state of ...
Page 118
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 4.4.3 Peripheral Configuration Submenu To access this submenu, select Advanced on the menu bar, then Peripheral Configuration. Maintenance Main The submenu represented in Table 69 is used for configuring computer peripherals. Table 69. Peripheral Configuration Submenu Feature Options • Disabled Serial Port A • ...
Page 119
Table 69. Peripheral Configuration Submenu (continued) Feature Options • Disabled Parallel Port • Enabled • Auto (default) • Output Only Mode • Bi-directional (default) • EPP • ECP • 378 (default) Base I/O Address (This feature is present • 278 ...
Page 120
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 4.4.4 IDE Configuration Submenu To access this submenu, select Advanced on the menu bar, then IDE Configuration. Maintenance Main The menu represented in Table 70 is used to configure IDE device options. Table 70. IDE Configuration Submenu Feature Options • Disabled IDE Controller • ...
Page 121
Primary/Secondary IDE Master/Slave Submenus To access these submenus, select Advanced on the menu bar, then IDE Configuration, and then the master or slave to be configured. Maintenance Main There are four IDE submenus: primary master, primary slave, secondary master, ...
Page 122
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification Table 71. Primary/Secondary IDE Master/Slave Submenus (continued) Feature Options • Auto (Note) PIO Mode • 0 • 1 • 2 • 3 (default) • 4 • Disabled Ultra DMA • Mode 0 • Mode 1 • Mode 2 (default) • Mode 3 • Mode 4 ...
Page 123
Diskette Configuration Submenu To access this menu, select Advanced on the menu bar, then Diskette Configuration. Maintenance Main The submenu represented by Table 72 is used for configuring the diskette drive. Table 72. Diskette Configuration Submenu Feature Options • ...
Page 124
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 4.4.6 Event Log Configuration Submenu To access this menu, select Advanced on the menu bar, then Event Log Configuration. Maintenance Main The submenu represented by Table 73 is used to configure the event logging features. Table 73. Event Log Configuration Submenu ...
Page 125
Video Configuration Submenu To access this menu, select Advanced on the menu bar, then Video Configuration. Maintenance Main The submenu represented in Table 74 is for configuring the video features. Table 74. Video Configuration Submenu Feature Options • AGP ...
Page 126
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 4.5 Security Menu To access this menu, select Security from the menu bar at the top of the screen. Maintenance Main The menu represented by Table 75 is for setting passwords and security features. Table 75. Security Menu If no password entered previously: ...
Page 127
Power Menu To access this menu, select Power from the menu bar at the top of the screen. Maintenance Main The menu represented in Table 76 is for setting the power management features. Table 76. Power Menu Feature Options ...
Page 128
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 4.6.1 APM Submenu To access this menu, select Power on the menu bar, then APM. Maintenance Main The submenu represented in Table 77 is for setting APM power options. Table 77. APM Submenu Feature Options • Disabled Power Management • ...
Page 129
ACPI Submenu To access this menu, select Power on the menu bar, then ACPI. Maintenance Main The submenu represented in Table 78 is for setting ACPI power options. Table 78. ACPI Submenu Feature Options • S1 State (default) ACPI ...
Page 130
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 4.7 Boot Menu To access this menu, select Boot from the menu bar at the top of the screen. Maintenance Main The menu represented in Table 79 is used to set the boot features and the boot sequence. Table 79. ...
Page 131
... After the predefined boot device types (removable devices, hard drives, and ATAPI CD-ROM drives), the entries in this list will reflect as many boot entry vector (BEV) boot devices (for example, Intel UNDI, PXE devices) and SCSI CD-ROM drives as are installed the five BEV boot devices supported by the BIOS. ...
Page 132
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 4.7.2 Hard Disk Drives Submenu To access this menu, select Boot on the menu bar, then Hard Disk Drives. Maintenance Main The submenu represented in Table 81 is for setting hard disk drive priority. Table 81. Hard Disk Drives Submenu ...
Page 133
ATAPI CDROM Drives Submenu To access this menu, select Boot on the menu bar, then ATAPI CDROM Drives. Maintenance Main The submenu represented in Table 83 is for setting ATAPI CDROM drive priority. Table 83. ATAPI CDROM Drives Submenu ...
Page 134
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 134 ...
Page 135
Error Messages and Beep Codes What This Chapter Contains 5.1 BIOS Error Messages...............................................................................................135 5.2 Port 80h POST Codes..............................................................................................137 5.3 Bus Initialization Checkpoints ...................................................................................141 5.4 Speaker ...................................................................................................................142 5.5 BIOS Beep Codes ....................................................................................................143 5.1 BIOS Error Messages Table 85 lists the ...
Page 136
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification Table 85. BIOS Error Messages (continued) Error Message Checking NVRAM..... Update OK! Updated Failed Keyboard Error KB/Interface Error Memory Size Decreased Memory Size Increased Memory Size Changed No Boot Device Available Off Board Parity Error On Board Parity Error ...
Page 137
... Onboard Floppy Controller (if any) is initialized. Compressed recovery code is uncompressed in F000:0000 in Shadow RAM and give control to recovery code in F000 Shadow RAM. Initialize interrupt vector tables, initialize system timer, initialize DMA controller and interrupt controller. E8 Initialize extra (Intel Recovery) Module. E9 Initialize floppy drive. EA Try to boot from floppy ...
Page 138
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification Table 88. Runtime Code Uncompressed in F000 Shadow RAM Code Description of POST Operation 03 NMI is Disabled. To check soft reset/power-on. 05 BIOS stack set. Going to disable cache if any. 06 POST code to be uncompressed. 07 CPU init and CPU data area init to be done. ...
Page 139
Table 88. Runtime Code Uncompressed in F000 Shadow RAM (continued) Code Description of POST Operation 40 To prepare the descriptor tables enter in virtual mode for memory test enable interrupts for diagnostics mode initialize ...
Page 140
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification Table 88. Runtime Code Uncompressed in F000 Shadow RAM (continued) Code Description of POST Operation 84 Lock-key checking over. To check for memory size mismatch with CMOS. 85 Memory size check done. To display soft error and check for password or bypass setup. ...
Page 141
Table 88. Runtime Code Uncompressed in F000 Shadow RAM (continued) Code Description of POST Operation AE Uncompress SMBIOS module and init SMBIOS code and form the runtime SMBIOS image in shadow. B1 Going to copy any code to specific area. ...
Page 142
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification Table 91 describes the lower nibble of the high byte and indicates the bus on which the routines are being executed. Table 91. Lower Nibble High Byte Functions Value Description 0 Generic DIM (Device Initialization Manager) 1 Onboard system devices ...
Page 143
BIOS Beep Codes Whenever a recoverable error occurs during POST, the BIOS displays an error message describing the problem (see Table 92). The BIOS also issues a beep code (one long tone followed by two short tones) during POST ...
Page 144
... Intel Desktop Board D815EFV/D815EPFV Technical Product Specification 5.6 Diagnostic LEDs (Optional) The optional enhanced diagnostics feature consists of a hardware decoder and four LEDs located between the LAN connector and the parallel port connector on the back panel. This feature requires no modifications to the chassis (other than I/O back panel shield) or cabling. ...
Page 145
Table 93. Diagnostic LED Codes Display BIOS Operation Amber Power on, starting BIOS Amber Amber Amber Green Recovery mode Amber Amber Amber Amber Processor, cache, etc. Green Amber Amber Green Memory, auto-size, shadow, Green etc. Amber Amber Amber PCI bus ...