XRP7740ILB-0X18-F Exar Corporation, XRP7740ILB-0X18-F Datasheet - Page 14

• Manufacturer Part Number: XRP7740ILB-0X18-F
• Description: IC CTRLR PWM/LDO STP-DWN 40TQFN
• Manufacturer: Exar Corporation
• Series: -r

Specifications of XRP7740ILB-0X18-F

• Topology: Step-Down (Buck) Synchronous (4), Linear (LDO) (1)
• Function: Any Function
• Number Of Outputs: 5
• Frequency - Switching: 1.5MHz
• Voltage/current - Output 1: Controller
• Voltage/current - Output 2: Controller
• Voltage/current - Output 3: Controller
• W/led Driver: No
• W/supervisor: No
• W/sequencer: Yes
• Voltage - Supply: 6.5 V ~ 20 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: *
• Package / Case: *
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 1016-1697

S
This 100mA low drop-out regulator can be programmed as 3.3V or 5V in SET_STBLDO_EN_CONFIG
register. Its output is seen on the LDOOUT Pin. This LDO is fully controllable via the Enable Pin
(configured to turn on as soon as power is applied), a GPIO, and/or I
The standby LDO should be bypassed with a minimum of 2.2uF ceramic capacitor.
E
The XRP7708 is enabled via raising the ENABLE Pin high.
lowering the same ENABLE Pin.
SOFTRESET Command.
For enabling a specific channel, there are several ways that this can be achieved. The chip can be
configured to enable a channel at start-up as the default configuration residing in the non-volatile
configuration memory of the IC. The channels can also be enabled using GPIO pins and/or an I
Bus serial command. The registers that control the channel enable functions are the
SET_EN_CONFIG and SET_CH_EN_I2C.
I
The XRP7708 integrates Internal Gate Drivers for all 4 PWM channels. These drivers are optimized
to drive both high-side and low side N-MOSFETs for synchronous operation. Both high side and low
side drivers have the capability of driving 1 nF load with 30 ns rise and fall time. The drivers have
built-in non-overlapping circuitry to prevent simultaneous conduction of the two MOSFETs.
F
While the chip is operating there are four different types of fault handling:
© 2011 Exar Corporation
NTERNAL
AULT
TANDBY
NABLING
•
•
•
Under Voltage Lockout (UVLO) monitors the input voltage to the chip, and the chip will
shutdown all channels if the voltage drops to critical levels.
Over Temperature Protection (OTP) monitors the temperature of the chip, and the chip
will shutdown all channels if the temperature rises to critical levels.
Over Voltage Protection (OVP) monitors the voltage of channel and will shutdown the
channel if it surpasses its voltage threshold.
H
ANDLING
L
, D
G
OW
ATE
ISABLING AND
D
D
ROP
RIVERS
-
OUT
R
Fig. 190: VCCA (green) Startup Waveform
EGULATOR
R
ESET
Q
Q
u
u
There is also the capability for resetting the Chip via an I
a
a
d
d
C
C
h
h
a
a
n
n
14/28
n
n
e
e
l
l
D
D
i
i
g
g
i
i
t
t
a
a
l
l
P
P
X
X
The chip can then be disabled by
W
W
R
R
M
M
P
P
2
S
C communication.
S
7
7
t
t
7
7
e
e
0
0
p
p
8
8
D
D
o
o
a
a
w
w
n
n
n
d
n
d
C
C
X
X
o
o
R
R
n
n
P
P
t
t
Rev. 1.2.0
r
r
7
7
o
o
7
7
l
l
l
l
e
e
4
4
r
r
2
2
0
0
s
C
C
s