P80C32X2BBD NXP Semiconductors, P80C32X2BBD Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
P80C32X2BBD
Manufacturer Part Number
P80C32X2BBD
Description
MCU 8-Bit 80C 80C51 CISC ROMLess 5V 44-Pin LQFP Tray
Manufacturer
NXP Semiconductors
Datasheet
1.P87C52X2BN112.pdf
(62 pages)
Specifications of P80C32X2BBD
Package
44LQFP
Device Core
80C51
Family Name
80C
Maximum Speed
33 MHz
Ram Size
256 Byte
Operating Supply Voltage
5 V
Data Bus Width
8 Bit
Program Memory Type
ROMLess
Number Of Programmable I/os
32
Interface Type
UART
Operating Temperature
0 to 70 °C
Number Of Timers
3
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
P80C32X2BBD
Manufacturer:
ABRACON
Quantity:
2 000
Part Number:
P80C32X2BBD
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
P80C32X2BBD,157
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
P80C32X2BBDЈ¬157
Manufacturer:
PH3
Quantity:
800
Philips Semiconductors
OSCILLATOR CHARACTERISTICS
Using the oscillator
XTAL1 and XTAL2 are the input and output, respectively, of an
inverting amplifier. The pins can be configured for use as an on-chip
oscillator, as shown in the logic symbol.
To drive the device from an external clock source, XTAL1 should be
driven while XTAL2 is left unconnected. However, minimum and
maximum high and low times specified in the data sheet must be
observed.
Clock Control Register (CKCON)
This device provides control of the 6-clock/12-clock mode by both
an SFR bit (bit X2 in register CKCON and an OTP bit (bit OX2).
When X2 is 0, 12-clock mode is activated. By setting this bit to 1, the
system is switching to 6-clock mode. Having this option
implemented as SFR bit, it can be accessed anytime and changed
to either value. Changing X2 from 0 to 1 will result in executing user
code at twice the speed, since all system time intervals will be
divided by 2. Changing back from 6-clock to 12-clock mode will slow
down running code by a factor of 2.
The OTP clock control bit (OX2) activates the 6-clock mode when
programmed using a parallel programmer, superceding the X2 bit
(CKCON.0). Please also see Table 2 below.
Table 2.
Programmable Clock-Out
A 50% duty cycle clock can be programmed to be output on P1.0.
This pin, besides being a regular I/O pin, has two alternate
functions. It can be programmed:
1. to input the external clock for Timer/Counter 2, or
2. to output a 50% duty cycle clock ranging from 61 Hz to 4 MHz at
To configure the Timer/Counter 2 as a clock generator, bit C/T2 (in
T2CON) must be cleared and bit T20E in T2MOD must be set. Bit
TR2 (T2CON.2) also must be set to start the timer.
The Clock-Out frequency depends on the oscillator frequency and
the reload value of Timer 2 capture registers (RCAP2H, RCAP2L)
as shown in this equation:
Where:
In the Clock-Out mode Timer 2 roll-overs will not generate an
interrupt. This is similar to when it is used as a baud-rate generator.
It is possible to use Timer 2 as a baud-rate generator and a clock
2003 Jan 24
OX2 clock mode bit
(can only be set by
parallel programmer)
erased
erased
programmed
80C51 8-bit microcontroller family
4K/8K/16K/32K ROM/OTP, low voltage (2.7 to 5.5 V),
low power, high speed (30/33 MHz)
n = 2 in 6-clock mode, 4 in 12-clock mode.
(RCAP2H,RCAP2L) = the content of RCAP2H and RCAP2L
taken as a 16-bit unsigned integer.
a 16 MHz operating frequency in 12-clock mode (122 Hz to
8 MHz in 6-clock mode).
n
(65536–RCAP2H, RCAP2L)
Oscillator Frequency
X2 bit
(CKCON.0)
0
1
X
CPU clock mode
12-clock mode
(default)
6-clock mode
6-clock mode
13
in 12-clock mode, unless it has been set to 6-clock operation using a
consumption by lowering the clock frequency down to any value. For
Either a hardware reset or external interrupt can be used to exit from
Power Down) enables or disables the wakeup from power down with
generator simultaneously. Note, however, that the baud-rate and the
Clock-Out frequency will be the same.
RESET
A reset is accomplished by holding the RST pin HIGH for at least
two machine cycles (24 oscillator periods in 12-clock and 12
oscillator periods in 6-clock mode), while the oscillator is running. To
insure a reliable power-up reset, the RST pin must be high long
enough to allow the oscillator time to start up (normally a few
milliseconds) plus two machine cycles. After the reset, the part runs
parallel programmer.
LOW POWER MODES
Stop Clock Mode
The static design enables the clock speed to be reduced down to
0 MHz (stopped). When the oscillator is stopped, the RAM and
Special Function Registers retain their values. This mode allows
step-by-step utilization and permits reduced system power
lowest power consumption the Power Down mode is suggested.
Idle Mode
In idle mode (see Table 3), the CPU puts itself to sleep while all of
the on-chip peripherals stay active. The instruction to invoke the idle
mode is the last instruction executed in the normal operating mode
before the idle mode is activated. The CPU contents, the on-chip
RAM, and all of the special function registers remain intact during
this mode. The idle mode can be terminated either by any enabled
interrupt (at which time the process is picked up at the interrupt
service routine and continued), or by a hardware reset which starts
the processor in the same manner as a power-on reset.
Power-Down Mode
To save even more power, a Power Down mode (see Table 3) can
be invoked by software. In this mode, the oscillator is stopped and
the instruction that invoked Power Down is the last instruction
executed. The on-chip RAM and Special Function Registers retain
their values down to 2.0 V and care must be taken to return V
the minimum specified operating voltages before the Power Down
Mode is terminated.
Power Down. Reset redefines all the SFRs but does not change the
on-chip RAM. An external interrupt allows both the SFRs and the
on-chip RAM to retain their values. WUPD (AUXR1.3–Wakeup from
external interrupt. Where:
To properly terminate Power Down, the reset or external interrupt
should not be executed before V
operating level and must be held active long enough for the
oscillator to restart and stabilize (normally less than 10 ms).
To terminate Power Down with an external interrupt, INT0 or INT1
must be enabled and configured as level-sensitive. Holding the pin
low restarts the oscillator but bringing the pin back high completes
the exit. Once the interrupt is serviced, the next instruction to be
executed after RETI will be the one following the instruction that put
the device into Power Down.
WUPD = 0: Disable
WUPD = 1: Enable
P80C3xX2; P80C5xX2;
CC
is restored to its normal
P87C5xX2
Product data
CC
to