SP3508EB Exar Corporation, SP3508EB Datasheet
SP3508EB
Specifications of SP3508EB
Related parts for SP3508EB
SP3508EB Summary of contents
Page 1
FEATURES Easy Evaluation of SP3508 Multi-Protocol Transceiver Eight (8) Drivers and Eight (8) Receivers Current Mode V.35 Drivers Internal Line or Digital Loopback Internal Transceiver Termination Resistors for V.11 and V.35 Termination Network Disable Option Fast 20Mbps Differential Transmission Rates ...
Page 2
Figure 1 Date: 8/26/04 SP3508 Evaluation Board Manual 2 JP41 JP33 JP40 JP32 JP31 JP39 JP38 JP30 JP29 JP37 JP28 JP36 JP27 JP35 JP26 JP34 © Copyright 2004 Sipex Corporation ...
Page 3
BOARD LAYOUT 1. The SP3508 Evaluation Board has been designed to easily and conveniently provide access to all inputs and outputs under test. 2. Figure schematic of the evaluation board. The schematic shows the location of the ...
Page 4
Figure 3. SP3508 Evaluation Board Layout N Date: 8/26/ ...
Page 5
Figure 4. SP3508 Evaluation Board Ground Plane Figure 5. SP3508 Evaluation Board V Date: 8/26/04 Plane CC SP3508 Evaluation Board Manual 5 © Copyright 2004 Sipex Corporation ...
Page 6
Figure 6. SP3508 Evaluation Board Layout Bottom Layer Date: 8/26/04 SP3508 Evaluation Board Manual 6 © Copyright 2004 Sipex Corporation ...
Page 7
TABLE 1. EIA-232 Signal Name source Mnemonic Shield — — Transmitted data DTE BA Received Data DCE BB Request To Send DTE CA Clear To Send DCE CB DCE Ready (DSR) DCE CC DTE Ready (DTR) DTE CD Signal Ground ...
Page 8
Recommended Equipment • Oscilloscope • Digital multimeter • Signal Generator capable of >40MHz • Communications Analyzer (such as Firebird 6000) Parametric Evaluation Located on the board are two pins identified as VCC and SIGNAL GND. Connect VCC to a +3.3V ...
Page 9
Driver/Receiver Remote Loopback The following example uses the ST driver looped back into the TxC receiver. Use the 3 bit decoder to configure the SP3508 for the desired protocol. Connect a jumper cable between the ST(a) pin and the TxC(a) ...
Page 10
TABLE 2 Driver V.35 EIA-530 Output Pin Mode Mode MODE (D0,D1,D2) 001 010 T1OUT(a) V.35 V.11 T1OUT(b) V.35 V.11 T2OUT(a) V.35 V.11 T2OUT(b) V.35 V.11 T3OUT(a) V.35 V.11 T3OUT(b) V.35 V.11 T4OUT(a) V.28 V.11 T4OUT(b) High-Z V.11 T5OUT(a) V.28 V.11 ...
Page 11
Figure 8 shows 3-pin jumper configuration and Table 5 describes the fuctionalities of each jumper setting configuration. TABLE 5. SP3508 LOGIC JUMPER SETTING Switch Jumper LOGIC 1 D0 JP22 VCC (2-3) D1 JP23 VCC (2-3) D2 JP24 VCC (2-3) LOOPBACK ...
Page 12
Pin Number Pin Name Description 1 GND Signal Ground 2 SDEN TxD Driver Enable Input 3 TTEN TxCE Driver Enable Input 4 STEN ST Driver Enable Input 5 RSEN RTS Driver Enable Input 6 TREN DTR Driver Enable Input 7 ...
Page 13
Model SP3508CF ........................................................ 0°C TO +70°C ..................................... 100-pin JEDEC LQFP SP3508CEB ..................................................... 0°C TO +70°C ............................... SP3508 Evaluation Board Corporation ANALOG EXCELLENCE Sipex Corporation Headquarters and Sales Office 233 South Hillview Drive Milpitas, CA 95035 TEL: (408) 934-7500 FAX: (408) ...