LPC2420FBD208-S NXP Semiconductors, LPC2420FBD208-S Datasheet - Page 38
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
LPC2420FBD208-S
Manufacturer Part Number
LPC2420FBD208-S
Description
MCU 16-Bit/32-Bit LPC2000 ARM7TDMI-S RISC ROMLess 3.3V 208-Pin LQFP Tray
Manufacturer
NXP Semiconductors
Datasheet
1.LPC2460FBD208551.pdf
(79 pages)
Specifications of LPC2420FBD208-S
Package
208LQFP
Device Core
ARM7TDMI-S
Family Name
LPC2000
Maximum Speed
72 MHz
Ram Size
82 KB
Operating Supply Voltage
3.3 V
Data Bus Width
16|32 Bit
Program Memory Type
ROMLess
Number Of Programmable I/os
160
Interface Type
I2C/I2S/SPI/SSP/UART/USB
On-chip Adc
8-chx10-bit
On-chip Dac
1-chx10-bit
Operating Temperature
-40 to 85 °C
Number Of Timers
4
NXP Semiconductors
LPC2420_60_5
Preliminary data sheet
7.21.1 Features
7.21 Pulse width modulator
The PWM is based on the standard Timer block and inherits all of its features, although
only the PWM function is pinned out on the LPC2420/2460. The Timer is designed to
count cycles of the system derived clock and optionally switch pins, generate interrupts or
perform other actions when specified timer values occur, based on seven match registers.
The PWM function is in addition to these features and is based on match register events.
The ability to separately control rising and falling edge locations allows the PWM to be
used for more applications. For instance, multi-phase motor control typically requires
three non-overlapping PWM outputs with individual control of all three pulse widths and
positions.
Two match registers can be used to provide a single edge controlled PWM output. A
dedicated match register controls the PWM cycle rate, by resetting the count upon match.
The other match register controls the PWM edge position. Additional single edge
controlled PWM outputs require only one match register each, since the repetition rate is
the same for all PWM outputs. Multiple single edge controlled PWM outputs will all have a
rising edge at the beginning of each PWM cycle, when an PWMMR0 match occurs.
Three match registers can be used to provide a PWM output with both edges controlled.
Again, a dedicated match register controls the PWM cycle rate. The other match registers
control the two PWM edge positions. Additional double edge controlled PWM outputs
require only two match registers each, since the repetition rate is the same for all PWM
outputs.
With double edge controlled PWM outputs, specific match registers control the rising and
falling edge of the output. This allows both positive going PWM pulses (when the rising
edge occurs prior to the falling edge), and negative going PWM pulses (when the falling
edge occurs prior to the rising edge).
•
•
•
•
– Do nothing on match.
LPC2420/2460 has two PWMs with the same operational features. These may be
operated in a synchronized fashion by setting them both up to run at the same rate,
then enabling both simultaneously. PWM0 acts as the master and PWM1 as the slave
for this use.
Counter or Timer operation (may use the peripheral clock or one of the capture inputs
as the clock source).
Seven match registers allow up to 6 single edge controlled or 3 double edge
controlled PWM outputs, or a mix of both types. The match registers also allow:
– Continuous operation with optional interrupt generation on match.
– Stop timer on match with optional interrupt generation.
– Reset timer on match with optional interrupt generation.
Supports single edge controlled and/or double edge controlled PWM outputs. Single
edge controlled PWM outputs all go HIGH at the beginning of each cycle unless the
output is a constant LOW. Double edge controlled PWM outputs can have either edge
occur at any position within a cycle. This allows for both positive going and negative
going pulses.
Rev. 05 — 24 February 2010
Flashless 16-bit/32-bit microcontroller
LPC2420/2460
© NXP B.V. 2010. All rights reserved.
38 of 79