SC16IS762IPW,128 NXP Semiconductors, SC16IS762IPW,128 Datasheet - Page 26
![IC DUAL UART 64BYTE 28TSSOP](/photos/6/52/65262/568-28-tssop_sot361-1_sml.jpg)
SC16IS762IPW,128
Manufacturer Part Number
SC16IS762IPW,128
Description
IC DUAL UART 64BYTE 28TSSOP
Manufacturer
NXP Semiconductors
Type
IrDA or RS- 232 or RS- 485r
Datasheet
1.SC16IS752IBS151.pdf
(59 pages)
Specifications of SC16IS762IPW,128
Number Of Channels
2, DUART
Package / Case
28-TSSOP (0.173", 4.40mm Width)
Features
Low Current
Fifo's
64 Byte
Protocol
RS232, RS485
Voltage - Supply
2.5V, 3.3V
With Auto Flow Control
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
Mounting Type
Surface Mount
Data Rate
5 Mbps
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.3 V
Supply Current
6 mA
Maximum Operating Temperature
+ 95 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Operating Supply Voltage
2.5 V or 3.3 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
568-4000 - DEMO BOARD SPI/I2C TO DUAL UART568-3510 - DEMO BOARD SPI/I2C TO UART
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
935279294128
SC16IS762IPW-F
SC16IS762IPW-F
SC16IS762IPW-F
SC16IS762IPW-F
NXP Semiconductors
SC16IS752_SC16IS762_7
Product data sheet
8.7 Modem Control Register (MCR)
The MCR controls the interface with the mode, data set, or peripheral device that is
emulating the modem.
Table 19.
[1]
Bit
7
6
5
4
3
2
1
0
MCR[7:5] and MCR[2] can only be modified when EFR[4] is set, that is, EFR[4] is a write enable.
Symbol
MCR[7]
MCR[6]
MCR[5]
MCR[4]
MCR[3]
MCR[2]
MCR[1]
MCR[0]
Modem Control Register bits description
[1]
[1]
[1]
Table 19
Dual UART with I
Description
Clock divisor.
IrDA mode enable.
Xon Any.
Enable loopback.
reserved
TCR and TLR enable.
RTS
DTR. If GPIO5 or GPIO1 is selected as DTR modem pin through
IOControl register bit 1 or bit 2, the state of DTR pin can be controlled as
below. Writing to IOState bit 5 or bit 1 will not have any effect on the DTR
pin.
Rev. 07 — 19 May 2008
logic 0 = divide-by-1 clock input
logic 1 = divide-by-4 clock input
logic 0 = normal UART mode
logic 1 = IrDA mode
logic 0 = disable Xon Any function
logic 1 = enable Xon Any function
logic 0 = normal operating mode
logic 1 = enable local Loopback mode (internal). In this mode the
MCR[1:0] signals are looped back into MSR[4:5] and the TX output is
looped back to the RX input internally.
logic 0 = disable the TCR and TLR register
logic 1 = enable the TCR and TLR register
logic 0 = force RTS output to inactive (HIGH)
logic 1 = force RTS output to active (LOW). In Loopback mode,
controls MSR[4]. If Auto-RTS is enabled, the RTS output is controlled
by hardware flow control.
logic 0 = force DTR output to inactive (HIGH)
logic 1 = force DTR output to active (LOW)
shows Modem Control Register bit settings.
2
SC16IS752/SC16IS762
C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
© NXP B.V. 2008. All rights reserved.
26 of 59