SC16IS762IPW,128 NXP Semiconductors, SC16IS762IPW,128 Datasheet - Page 30
![IC DUAL UART 64BYTE 28TSSOP](/photos/6/52/65262/568-28-tssop_sot361-1_sml.jpg)
SC16IS762IPW,128
Manufacturer Part Number
SC16IS762IPW,128
Description
IC DUAL UART 64BYTE 28TSSOP
Manufacturer
NXP Semiconductors
Type
IrDA or RS- 232 or RS- 485r
Datasheet
1.SC16IS752IBS151.pdf
(59 pages)
Specifications of SC16IS762IPW,128
Number Of Channels
2, DUART
Package / Case
28-TSSOP (0.173", 4.40mm Width)
Features
Low Current
Fifo's
64 Byte
Protocol
RS232, RS485
Voltage - Supply
2.5V, 3.3V
With Auto Flow Control
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
Mounting Type
Surface Mount
Data Rate
5 Mbps
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.3 V
Supply Current
6 mA
Maximum Operating Temperature
+ 95 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Operating Supply Voltage
2.5 V or 3.3 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
568-4000 - DEMO BOARD SPI/I2C TO DUAL UART568-3510 - DEMO BOARD SPI/I2C TO UART
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
935279294128
SC16IS762IPW-F
SC16IS762IPW-F
SC16IS762IPW-F
SC16IS762IPW-F
NXP Semiconductors
SC16IS752_SC16IS762_7
Product data sheet
8.13 Transmitter FIFO Level register (TXLVL)
8.14 Receiver FIFO Level register (RXLVL)
8.15 Programmable I/O pins Direction register (IODir)
8.16 Programmable I/O pins State register (IOState)
This register is a read-only register. It reports the number of spaces available in the
transmit FIFO.
Table 24.
This register is a read-only register, it reports the fill level of the receive FIFO, that is, the
number of characters in the RX FIFO.
Table 25.
This register is used to program the I/O pins direction. Bit 0 to bit 7 controls GPIO0 to
GPIO7.
Table 26.
When ‘read’, this register returns the actual state of all I/O pins. When ‘write’, each
register bit will be transferred to the corresponding I/O pin programmed as output.
Table 27.
Bit
7
6:0
Bit
7
6:0
Bit
7:0
Bit
7:0
Symbol
-
TXLVL[6:0]
Symbol
-
RXLVL[6:0]
Symbol
IODir
Symbol
IOState
Transmitter FIFO Level register bits description
Receiver FIFO Level register bits description
IODir register bits description
IOState register bits description
Dual UART with I
Rev. 07 — 19 May 2008
Description
not used; set to zeros
number of spaces available in TX FIFO, from 0 (0x00) to 64 (0x40)
Description
not used; set to zeros
number of characters stored in RX FIFO, from 0 (0x00) to 64 (0x40)
Description
Set GPIO pins [7:0] to input or output.
Description
Write this register: set the logic level on the output pins
Read this register: return states of all pins
0 = input
1 = output
0 = set output pin to zero
1 = set output pin to one
2
SC16IS752/SC16IS762
C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
© NXP B.V. 2008. All rights reserved.
30 of 59