SC16C2550IB48,128 NXP Semiconductors, SC16C2550IB48,128 Datasheet - Page 17
![IC DUART SOT313-2](/photos/31/31/313101/sot313-2_sml.jpg)
SC16C2550IB48,128
Manufacturer Part Number
SC16C2550IB48,128
Description
IC DUART SOT313-2
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C2550IN40112.pdf
(46 pages)
Specifications of SC16C2550IB48,128
Features
2 Channels
Number Of Channels
2, DUART
Fifo's
16 Byte
Voltage - Supply
3.5 V ~ 4.5 V
With Auto Flow Control
Yes
With Irda Encoder/decoder
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Package / Case
48-LQFP
Transmit Fifo
16Byte
Receive Fifo
16Byte
Transmitter And Receiver Fifo Counter
Yes
Data Rate
5Mbps
Package Type
LQFP
Operating Supply Voltage (max)
5.5V
Mounting
Surface Mount
Pin Count
48
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
935270020128
SC16C2550IB48-T
SC16C2550IB48-T
SC16C2550IB48-T
SC16C2550IB48-T
Philips Semiconductors
9397 750 11621
Product data
7.1 Transmit (THR) and Receive (RHR) Holding Registers
7.2 Interrupt Enable Register (IER)
The serial transmitter section consists of an 8-bit Transmit Hold Register (THR) and
Transmit Shift Register (TSR). The status of the THR is provided in the Line Status
Register (LSR). Writing to the THR transfers the contents of the data bus (D7-D0) to
the TSR and UART via the THR, providing that the THR is empty. The THR empty
flag in the LSR register will be set to a logic 1 when the transmitter is empty or when
data is transferred to the TSR. Note that a write operation can be performed when the
THR empty flag is set (logic 0 = at least one byte in FIFO/THR, logic 1 = FIFO/THR
empty).
The serial receive section also contains an 8-bit Receive Holding Register (RHR) and
a Receive Serial Shift Register (RSR). Receive data is removed from the SC16C2550
and receive FIFO by reading the RHR register. The receive section provides a
mechanism to prevent false starts. On the falling edge of a start or false start bit, an
internal receiver counter starts counting clocks at the 16 clock rate. After 7-
clocks, the start bit time should be shifted to the center of the start bit. At this time the
start bit is sampled, and if it is still a logic 0 it is validated. Evaluating the start bit in
this manner prevents the receiver from assembling a false character. Receiver status
codes will be posted in the LSR.
The Interrupt Enable Register (IER) masks the interrupts from receiver ready,
transmitter empty, line status and modem status registers. These interrupts would
normally be seen on the INTA, INTB output pins.
Table 8:
Bit
7
6
5
4
3
Interrupt Enable Register bits description
Symbol
IER[7]
IER[6]
IER[5]
IER[4]
IER[3]
Dual UART with 16 bytes of transmit and receive FIFOs and IrDA
Rev. 03 — 19 June 2003
Description
CTS interrupt.
RTS interrupt.
Xoff interrupt.
Sleep mode.
Modem Status Interrupt. This interrupt will be issued whenever
there is a modem status change as reflected in MSR[0-3].
Logic 0 = Disable the CTS interrupt (normal default condition).
Logic 1 = Enable the CTS interrupt. The SC16C2550 issues an
interrupt when the CTS pin transitions from a logic 0 to a logic 1.
Logic 0 = Disable the RTS interrupt (normal default condition).
Logic 1 = Enable the RTS interrupt. The SC16C2550 issues an
interrupt when the RTS pin transitions from a logic 0 to a logic 1.
Logic 0 = Disable the software flow control, receive Xoff interrupt
(normal default condition).
Logic 1 = Enable the software flow control, receive Xoff interrupt.
Logic 0 = Disable sleep mode (normal default condition).
Logic 1 = Enable sleep mode.
Logic 0 = Disable the modem status register interrupt (normal
default condition).
Logic 1 = Enable the modem status register interrupt.
© Koninklijke Philips Electronics N.V. 2003. All rights reserved.
SC16C2550
encoder/decoder
1
2
17 of 46