UPD3777CY NEC, UPD3777CY Datasheet
UPD3777CY
Related parts for UPD3777CY
UPD3777CY Summary of contents
Page 1
... CCD linear image sensor 22-pin plastic DIP (10.16 mm (400)) The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all devices/types available in every country. Please check with local NEC representative for availability and additional information. Document No. S14583EJ1V0DS00 (1st edition) ...
Page 2
BLOCK DIAGRAM V 2L GND OUT 21 (Blue OUT 22 (Green OUT 1 (Red) Clamp pulse generator GND 11 CCD analog shift register Transfer gate Photocell ...
Page 3
... Green photocell array Channel stopper 5.25 m Data Sheet S14583EJ1V0DS00 PD3777 2 Output signal 2 (Green) 1 Output signal 1 (Blue) No connection Output drain voltage No connection Last stage shift register clock 2 No connection No connection 1 Shift register clock 1 Transfer gate clock 1 TG1 (for Blue) Transfer gate clock 2 TG2 ...
Page 4
ABSOLUTE MAXIMUM RATINGS (T Parameter Output drain voltage V OD Shift register clock voltage V Reset gate clock voltage V Transfer gate clock voltage V Operating ambient temperature T A Storage temperature T stg Caution Exposure to ABSOLUTE MAXIMUM RATINGS ...
Page 5
ELECTRICAL CHARACTERISTICS data rate ( light source : 3200 K halogen lamp + C 500S (infrared cut filter mm (heat absorbing filter ...
Page 6
INPUT PIN CAPACITANCE ( Parameter Shift register clock pin capacitance 1 Shift register clock pin capacitance 2 Last stage shift register clock pin capacitance Reset gate clock pin capacitance Transfer gate clock pin capacitance 6 ...
Page 7
TIMING CHART 1 (for each color) TG1 to TG3 Note OUT V 3 OUT Note Input the RB pulse continuously during this period, too. Optical black Valid photocell (49 pixels) (5400 pixels) ...
Page 8
TIMING CHART 2 (for each color OUT ...
Page 9
TG1 to TG3 TIMING CHART TG1 to TG3 1 2 Symbol t1, t2 t1’, t2’ t5 t8, t9 t10, t11 1, 2 cross points 1 2 1L, 2 cross points ...
Page 10
DEFINITIONS OF CHARACTERISTIC ITEMS 1. Saturation voltage : V sat Output signal voltage at which the response linearity is lost. 2. Saturation exposure : SE Product of intensity of illumination (lx) and storage time (s) when saturation of output voltage ...
Page 11
Dark signal non-uniformity : DSNU Absolute maximum of the difference between ADS and voltage of the highest or lowest output pixel of all the valid pixels at light shielding. This is calculated by the following formula. DSNU (mV) : ...
Page 12
Random noise : Random noise is defined as the standard deviation of a valid pixel output signal with 100 times (= 100 lines) data sampling at dark (light shielding). 100 2 (V – (mV) ...
Page 13
STANDARD CHARACTERISTIC CURVES (Nominal) DARK OUTPUT TEMPERATURE CHARACTERISTIC 0.5 0.25 0 Operating Ambient Temperature T TOTAL SPECTRAL RESPONSE CHARACTERISTICS (without infrared cut filter and heat absorbing filter) (T 100 ...
Page 14
APPLICATION CIRCUIT EXAMPLE + F/ 150 4 Remark The inverters shown in the above application circuit example are the 74HC04 (data rate 74AC04 (data rate MHz). 14 ...
Page 15
PACKAGE DRAWING CCD LINEAR IMAGE SENSOR 22-PIN PLASTIC DIP (10.16 mm (400)) (Unit : mm) 1bit 0.5±0.3 37.5 44.0±0.3 1.02±0.15 0.46±0.1 25.4 (5.42) 2.54 4.21±0.5 4.39±0.4 Name Dimensions 42.9 8.35 Plastic cap 1 The bottom of the package 2 The ...
Page 16
RECOMMENDED SOLDERING CONDITIONS When soldering this product highly recommended to observe the conditions as shown below. If other soldering processes are used the soldering is performed under different conditions, please make sure to consult with our ...
Page 17
Data Sheet S14583EJ1V0DS00 PD3777 17 ...
Page 18
NOTES ON CLEANING THE PLASTIC CAP 1 CLEANING THE PLASTIC CAP Care should be taken when cleaning the surface to prevent scratches. The optical characteristics of the CCD will be degraded if the cap is scratched during cleaning. We recommend ...
Page 19
... HANDLING OF UNUSED INPUT PINS FOR CMOS Note: No connection for CMOS device inputs can be cause of malfunction connection is provided to the input pins possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry ...
Page 20
... Specific: Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance ...