UPD4701AC NEC, UPD4701AC Datasheet
UPD4701AC
Specifications of UPD4701AC
Available stocks
Related parts for UPD4701AC
UPD4701AC Summary of contents
Page 1
INCREMENTAL ENCODER COUNTER DESCRIPTION The PD4701A is a counter for 2-axis incremental encoder. When a two-phase encoder signal is input for the X and Y axes, direction discrimination and computation is performed, and count data is output ...
Page 2
ORDERING INFORMATION Part Number PD4701AC 24-pin plastic DIP (600 mil) PD4701AGT 24-pin plastic SOP (375 mil) BLOCK DIAGRAM Phase X A Determination and X Edge Detection B RESET X RESET Y Phase Y A Determination and Y Edge Detection B ...
Page 3
... Y counter 2-phase signal input pins Key switch input pins. Key switch input are read as the high-order 4 bits of the X counter and Y counter upper byte as the internal status. Upper Byte Key Input Status Count Data +5 V power supply connection pin Ground pin PD4701A ...
Page 4
DESCRIPTION OF OPERATIONS 1. COUNT OPERATION The PD4701A executes an up-count and down-count by means of A & B 2-phase signals in the 12-bit up-down counter. An up-count is performed when the A-phase signals (X performed when the B-phase signals ...
Page 5
SWITCH INPUT OPERATION The PD4701A can process contact points as switch inputs (active-“L” input). Switch input is read as part of the count data upper byte together with the switch flag status as an internal status ...
Page 6
... These are connected to a CPU output port or reset signal. RESET Y The above connections enable the CPU to read the X counter, Y counter and switch input status. The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. ...
Page 7
An example of a PD4701A data read is shown in Fig. 5. Fig. 5 Example of PD4701A Data Read Count value latch X counter low byte read X counter high byte & switch status read Y counter low byte read ...
Page 8
APPLICATION AREAS Two-phase incremental signals are used for detection and measurement of a vector quantity (a quantity that has direction and magnitude), and are widely employed in measuring instruments such as micrometers and linear scales, control systems for digital ...
Page 9
ABSOLUTE MAXIMUM RATINGS (T a PARAMETER Supply voltage Input voltage Output voltage Operating temperature Storage temperature Permissible loss DC CHARACTERISTICS (T = – PARAMETER Input voltage high Input voltage low Output voltage low Output voltage ...
Page 10
AC CHARACTERISTICS (T = – PARAMETER Input cycle High-level pulse width A B Low-level pulse width Signal phase difference time R, L High-level pulse width M Low-level ...
Page 11
Fig. 6 Two-Phase Signal & Switch Signal Input Timing t PWABH SAB RIGHT LEFT MIDDLE Fig. 7 Count Flag Output Timing t PWRS RESET SCTEN ...
Page 12
CS t SACS X/Y U/L t DCSD Fig. 9 Switch Flag Signal Output Timing RIGHT LEFT MIDDLE SF 12 Fig. 8 Data Output Timing t DAD t t DSFL DSFH PD4701A t HCSA t FCSD ...
Page 13
RECOMMENDED SOLDERING CONDITIONS The following conditions (see table below) must be met when soldering this product. Please consult with our sales offices in case other soldering process is used case soldering is done under different conditions. TYPES OF ...
Page 14
PLASTIC DIP (600 mil NOTES 1) Each lead centerline is located within 0.25 mm (0.01 inch) of its true position (T.P.) at maximum material condition. 2) Item "K" ...
Page 15
PIN PLASTIC SOP (375 mil NOTE Each lead centerline is located within 0.12 mm (0.005 inch) of its true position (T.P.) at maximum material condition. 13 detail of lead end 12 L ...
Page 16
... Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance ...