TDA8559T/N1,518 NXP Semiconductors, TDA8559T/N1,518 Datasheet - Page 11

• Manufacturer Part Number: TDA8559T/N1,518
• Description: IC AMP AUDIO .14W MONO AB 16SOIC
• Manufacturer: NXP Semiconductors
• Type: Class ABr

Specifications of TDA8559T/N1,518

• Package / Case: 16-SOIC (3.9mm Width)
• Output Type: 1-Channel (Mono) or 2-Channel (Stereo)
• Max Output Power X Channels @ Load: 140mW x 1 @ 25 Ohm; 35mW x 2 @ 32 Ohm
• Voltage - Supply: 1.9 V ~ 30 V
• Features: Depop, Differential Inputs, Mute, Short-Circuit Protection, Standby
• Mounting Type: Surface Mount
• Product: General Purpose Audio Amplifiers
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 935168790518; TDA8559TD-T; TDA8559TD-T

Philips Semiconductors
Table 7.
V
[1]
[2]
[3]
[4]
[5]
[6]
[7]
13. Application information
TDA8559_3
Product data sheets
Symbol
V
V
V
V
Z
V
SVRR
BTL application (R
P
THD
G
f
V
V
V
Z
V
SVRR
Line driver application (R
V
ss
P
i
i
no
no(mute)
o(mute)
mt
os
o
no
no(mute)
o(mute)
os
o
v
= 3 V; T
The supply voltage range at pin V
Measured with low-pass filter 30 kHz.
Noise output voltage measured with a bandwidth of 20 Hz to 20 kHz, unweighted. R
RMS output voltage in mute is measured with V
DC output offset voltage is measured between the signal output and the 0.5V
The ripple rejection is measured with a ripple voltage of 200 mV (RMS) applied to the positive supply rail (R
DC output offset voltage is measured between the two signal outputs.
amb
Characteristics
Parameter
noise output voltage
noise output voltage in
mute
output voltage in mute
mid-tap voltage
input impedance
DC output offset voltage
supply voltage ripple
rejection
output power
total harmonic distortion
voltage gain
small signal roll-off
frequency
noise output voltage
noise output voltage in
mute
output voltage in mute
input impedance
DC output offset voltage
supply voltage ripple
rejection
line output voltage
= 25 C; f
13.1 General
L
= 25 )
i
For applications with a maximum supply voltage of 6 V (input mode low) the input pins
need a DC path to ground (see
voltages in the range from 6 V to 18 V (input mode HIGH) the input DC level is
0.5V
have to be used.
= 1 kHz; unless otherwise specified.
L
…continued
= 1 k )
P
+ 0.6 V. In this situation the input configurations illustrated in
P1
is from 1.9 V to 18 V. Pin V
Conditions
THD = 10 %
P
P
1 dB
o
o
= 70 mW; f
= 70 mW; f
i
= 200 mV (RMS); f = 1 kHz.
Rev. 03 — 15 May 2006
i
i
= 1 kHz
= 10 kHz
Figure 3
P2
is used for the voltage range from 6 V to 30 V.
and
P
output.
[3]
[3]
[4]
[5]
[6]
[3]
[3]
[4]
[7]
[6]
Figure
Low-voltage stereo headphone amplifier
Min
-
-
-
1.4
75
-
45
125
-
-
31
-
-
-
-
39
-
39
0.1
s
= 5 k .
4). For applications with supply
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Typ
70
20
-
1.5
100
-
55
140
0.05
0.1
32
750
100
25
-
50
-
49
-
Figure 5
s
TDA8559T
= 0 k ).
Max
85
30
30
1.6
125
100
-
-
0.1
-
33
-
120
40
40
61
150
-
2.9
and
Figure 6
Unit
V
k
mV
dB
mW
%
%
dB
kHz
k
mV
dB
V
11 of 36
V
V
V
V
V
V