UPC3221GV-E1-A NEC, UPC3221GV-E1-A Datasheet
UPC3221GV-E1-A
Specifications of UPC3221GV-E1-A
Available stocks
Related parts for UPC3221GV-E1-A
UPC3221GV-E1-A Summary of contents
Page 1
... V TYP. CC • Embossed tape 8 mm wide • Pin 1 indicates pull-out direction of tape • Qty 1 kpcs/reel µ PC3221GV-A The mark shows major revised points. µ PC3221GV = 0.7 V /tone out p-p Supplying Form © NEC Compound Semiconductor Devices, Ltd. 2002, 2004 ...
Page 2
... INTERNAL BLOCK DIAGRAM AND PIN CONNECTIONS INPUT1 2 INPUT2 AGC PRODUCT LINE- AGC AMPLIFIER MAX Part Number (mA) (dB) µ PC3217GV 23 53 µ PC3218GV 23 63 µ PC3219GV 36.5 42.5 µ PC3221GV 33 60 Note MHz MHz out 2 (Top View) 8 AGC AMP. Video AMP AGC Control ...
Page 3
... V AGC Recommended to use AGC voltage with externally resister (example: 1 kΩ). Ground pin. This pin should be connected to system ground with minimum inductance. Ground pattern on the board should be formed as wide as possible. Signal output pins of video amplifier. This pin should be coupled with capacitor for DC cut ...
Page 4
ABSOLUTE MAXIMUM RATINGS Parameter Symbol Supply Voltage V Gain Control Voltage Range V Power Dissipation P Operating Ambient Temperature T Storage Temperature T Note Mounted on double-sided copper-clad 50 × 50 × 1.6 mm epoxy glass PWB RECOMMENDED OPERATING RANGE ...
Page 5
ELECTRICAL CHARACTERISTICS (T = +25° MHz Parameter Symbol DC Characteristics Circuit Current AGC Pin Current I AGC Voltage High Level V AGC (H) AGC Voltage Low Level V AGC (L) ...
Page 6
STANDARD CHARACTERISTICS (T Parameter Symbol Noise Figure 2 NF2 Noise Figure 3 NF3 Output Voltage V Input Impedance Z Output Impedance Z Input 3rd Order Distortion IIP Intercept Point Notes 1. By measurement circuit measurement circuit 3 ...
Page 7
MEASUREMENT CIRCUIT 1 V µ Signal Note µ Generator 50 Ω µ kΩ µ AGC Note Balun Transformer: TOKO 617DB-1010 B4F (Double balanced type) MEASUREMENT CIRCUIT µ ...
Page 8
MEASUREMENT CIRCUIT µ Note µ µ kΩ µ AGC Noise Source Note Balun Transformer: TOKO 617DB-1010 B4F (Double balanced type) MEASUREMENT CIRCUIT 4 µ ...
Page 9
ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD (MEASUREMENT CIRCUIT 1) Note Balun Transformer Remarks 1. Back side: GND pattern 2. Solder plated on pattern 3. : Through hole V CC µ 200 Ω µ Note µ ...
Page 10
TYPICAL CHARACTERISTICS (T CIRCUIT CURRENT vs. SUPPLY VOLTAGE 50 No input signal +25˚ +85˚ –40˚ Supply Voltage V (V) CC AGC ...
Page 11
OUTPUT POWER vs. INPUT POWER MHz V = 0.5 V AGC 5 –5 5.0 V –10 –15 –20 –25 –30 –80 –70 –60 –50 –40 –30 –20 –10 Input Power P ...
Page 12
NOISE FIGURE vs. GAIN CONTROL VOLTAGE RANGE 1.0 1.5 2.0 2.5 Gain Control Voltage Range V NOISE FIGURE vs. GAIN REDUCTION ...
Page 13
OUTPUT POWER, IM vs. INPUT POWER –10 P out –20 –30 5.5 V – 4 –50 5.0 V – –70 V AGC –80 freq1 = 44 MHz freq2 = 45 MHz ...
Page 14
S-PARAMETERS (T = +25° −FREQUENCY S 11 −FREQUENCY 5.0 V) AGC MHz MHz 3 : 100 MHz 1 : ...
Page 15
PACKAGE DIMENSIONS 8-PIN PLASTIC SSOP (4.45 mm (175)) (UNIT: mm 2.9±0.1 1.8 MAX. 1.5±0.1 0.65 +0.10 0.3 0.10 –0.05 0.1±0.1 5 detail of lead end 4 4.94±0.2 3.2±0.1 0.575 MAX. 0.5±0.2 M +0.10 0.15 –0.05 Data Sheet PU10171EJ03V0DS ...
Page 16
... Observe precautions for handling because of electro-static sensitive devices. (2) Form a ground pattern as widely as possible to minimize ground impedance (to prevent undesired oscillation). All the ground pins must be connected together with wide ground pattern to decrease impedance difference. (3) The bypass capacitor should be attached to V RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions ...
Page 17
... NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC semiconductor products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC or others. • ...
Page 18
... For further information, please contact NEC Compound Semiconductor Devices, Ltd. E-mail: salesinfo@ml.ncsd.necel.com (sales and general) techinfo@ml.ncsd.necel.com (technical) Sales Division TEL: +81-44-435-1588 FAX: +81-44-435-1579 NEC Compound Semiconductor Devices Hong Kong Limited E-mail: ncsd-hk@elhk.nec.com.hk (sales, technical and general) Hong Kong Head Office TEL: +852-3107-7303 TEL: +886-2-8712-0478 ...
Page 19
Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) ...