ATmega165PA Atmel Corporation, ATmega165PA Datasheet - Page 240

• Manufacturer Part Number: ATmega165PA
• Manufacturer: Atmel Corporation

Specifications of ATmega165PA

• Flash (kbytes): 16 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

25.3
25.3.1
25.3.2
25.3.2.1
25.3.2.2
25.3.2.3
25.3.3
8285D–AVR–06/11
Data Registers
Bypass Register
Device Identification Register
Reset Register
Version
Part Number
Manufacturer ID
ATmega165A/PA/325A/PA/3250A/PA/645A/P/6450A/P
The Data Registers relevant for Boundary-scan operations are:
• Bypass Register
• Device Identification Register
• Reset Register
• Boundary-scan Chain
The Bypass Register consists of a single Shift Register stage. When the Bypass Register is
selected as path between TDI and TDO, the register is reset to 0 when leaving the Capture-DR
controller state. The Bypass Register can be used to shorten the scan chain on a system when
the other devices are to be tested.
Figure 25-1
Figure 25-1. The Format of the Device Identification Register
Version is a 4-bit number identifying the revision of the component. The JTAG version number
follows the revision of the device. Revision A is 0x0, revision B is 0x1 and so on.
The part number is a 16-bit code identifying the component. The JTAG Part Number for
ATmega165A/165PA/325A/325PA/3250A/3250PA/645A/645P/6450A/6450P is listed in
27-6 on page
The Manufacturer ID is a 11-bit code identifying the manufacturer. The JTAG manufacturer ID
for ATMEL is 0x1F. See
The Reset Register is a test Data Register used to reset the part. Since the AVR tri-states Port
Pins when reset, the Reset Register can also replace the function of the unimplemented optional
JTAG instruction HIGHZ.
A high value in the Reset Register corresponds to pulling the external Reset low. The part is
reset as long as there is a high value present in the Reset Register. Depending on the fuse set-
tings for the clock options, the part will remain reset for a reset time-out period (refer to
Sources” on page
not latched, so the reset will take place immediately, as shown in
Bit
Device ID
shows the structure of the Device Identification Register.
MSB
31
286.
Version
4 bits
30) after releasing the Reset Register. The output from this Data Register is
28
Table 27-6 on page
27
Part Number
16 bits
286.
12
11
Figure 25-2 on page
Manufacturer ID
11 bits
1
241.
”Clock
Table
LSB
1-bit
1
0
240