ATmega16M1 Atmel Corporation, ATmega16M1 Datasheet - Page 63

• Manufacturer Part Number: ATmega16M1
• Manufacturer: Atmel Corporation

Specifications of ATmega16M1

• Flash (kbytes): 16 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 27
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Can: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 14
• Input Capture Channels: 1
• Pwm Channels: 10
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

12.2.7
12.2.8
12.2.9
8209D–AVR–11/10
PCMSK2 – Pin Change Mask Register 2
PCMSK1 – Pin Change Mask Register 1
PCMSK0 – Pin Change Mask Register 0
• Bit 7:0 – PCINT23:16: Pin Change Enable Mask 23:16
Each PCINT23:16-bit selects whether pin change interrupt is enabled on the corresponding I/O
pin. If PCINT23:16 is set and the PCIE2 bit in PCICR is set, pin change interrupt is enabled on
the corresponding I/O pin. If PCINT23:16 is cleared, pin change interrupt on the corresponding
I/O pin is disabled.
• Bit 7 – Res: Reserved
This bit is reservedand will always read as zero.
• Bit 7:0 – PCINT15:8: Pin Change Enable Mask 15:8
Each PCINT15:8-bit selects whether pin change interrupt is enabled on the corresponding I/O
pin. If PCINT15:8 is set and the PCIE1 bit in PCICR is set, pin change interrupt is enabled on the
corresponding I/O pin. If PCINT15:8 is cleared, pin change interrupt on the corresponding I/O
pin is disabled.
• Bit 7:0 – PCINT[7:0]: Pin Change Enable Mask 7:0
Each PCINT7:0 bit selects whether pin change interrupt is enabled on the corresponding I/O pin.
If PCINT7:0 is set and the PCIE0 bit in PCICR is set, pin change interrupt is enabled on the cor-
responding I/O pin. If PCINT7:0 is cleared, pin change interrupt on the corresponding I/O pin is
disabled.
Bit
Read/Write
Initial Value
Bit
Read/Write
Initial Value
Bit
Read/Write
Initial Value
PCINT23
R/W
7
PCINT7
R/W
0
PCINT15
7
0
R
7
0
PCINT22
6
PCINT6
R/W
0
R/W
PCINT14
6
0
R/W
6
0
PCINT21
PCINT5
R/W
5
0
R/W
PCINT13
5
0
R/W
5
0
PCINT20
4
PCINT4
R/W
0
PCINT12
R/W
4
0
R/W
4
0
ATmega16M1/32M1/64M1
PCINT19
3
PCINT3
R/W
0
PCINT11
R/W
3
0
R/W
3
0
PCINT18
2
PCINT2
R/W
0
PCINT10
R/W
2
0
R/W
2
0
PCINT17
1
PCINT1
R/W
0
PCINT9
R/W
R/W
1
0
1
0
0
PCINT0
R/W
0
PCINT16
PCINT8
R/W
R/W
0
0
0
0
PCMSK0
PCMSK2
PCMSK1
63