ATmega329 Atmel Corporation, ATmega329 Datasheet - Page 132

• Manufacturer Part Number: ATmega329
• Manufacturer: Atmel Corporation

Specifications of ATmega329

• Flash (kbytes): 32 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 100
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

16.11 Register Description
16.11.1
132
ATmega329/3290/649/6490
TCCR1A – Timer/Counter1 Control Register A
Figure 16-13. Timer/Counter Timing Diagram, with Prescaler (f
• Bit 7:6 – COM1A1:0: Compare Output Mode for Unit A
• Bit 5:4 – COM1B1:0: Compare Output Mode for Unit B
The COM1A1:0 and COM1B1:0 control the Output Compare pins (OC1A and OC1B respec-
tively) behavior. If one or both of the COM1A1:0 bits are written to one, the OC1A output
overrides the normal port functionality of the I/O pin it is connected to. If one or both of the
COM1B1:0 bit are written to one, the OC1B output overrides the normal port functionality of the
I/O pin it is connected to. However, note that the Data Direction Register (DDR) bit correspond-
ing to the OC1A or OC1B pin must be set in order to enable the output driver.
When the OC1A or OC1B is connected to the pin, the function of the COM1x1:0 bits is depen-
dent of the WGM13:0 bits setting.
WGM13:0 bits are set to a Normal or a CTC mode (non-PWM).
Table 16-2.
Bit
(0x80)
Read/Write
Initial Value
COM1A1/COM1B1
and ICF n
(PC and PFC PWM)
TOVn
(CTC and FPWM)
(Update at TOP)
0
0
1
1
TCNTn
TCNTn
OCRnx
(clk
as TOP)
clk
clk
COM1A1
I/O
(FPWM)
I/O
Tn
/8)
R/W
(if used
Compare Output Mode, non-PWM
7
0
COM1A0
COM1A0/COM1B0
R/W
6
0
TOP - 1
TOP - 1
0
1
0
1
COM1B1
R/W
Old OCRnx Value
5
0
Table 16-2
COM1B0
R/W
4
0
Description
Normal port operation, OC1A/OC1B
disconnected.
Toggle OC1A/OC1B on Compare Match.
Clear OC1A/OC1B on Compare Match (Set
output to low level).
Set OC1A/OC1B on Compare Match (Set output
to high level).
shows the COM1x1:0 bit functionality when the
TOP
TOP
R
3
–
0
R
2
–
0
BOTTOM
TOP - 1
clk_I/O
WGM11
R/W
1
0
New OCRnx Value
/8)
WGM10
R/W
0
0
BOTTOM + 1
TOP - 2
TCCR1A
2552K–AVR–04/11