ATxmega16D4 Atmel Corporation, ATxmega16D4 Datasheet - Page 15

• Manufacturer Part Number: ATxmega16D4
• Manufacturer: Atmel Corporation

Specifications of ATxmega16D4

• Flash (kbytes): 16 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Speed: No
• Usb Interface: No
• Spi: 4
• Twi (i2c): 2
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 12
• Adc Speed (ksps): 200
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 14
• Input Capture Channels: 14
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8. Event System
8.1
8.2
8135J–AVR–12/10
Features
Overview
•
•
•
•
•
•
•
•
•
The Event System is a set of features for inter-peripheral communication. It enables the possibil-
ity for a change of state in one peripheral to automatically trigger actions in other peripherals.
The change of state in a peripheral that will trigger actions in other peripherals is configurable in
software. It is a simple, but powerful system as it allows for autonomous control of peripherals
without any use of interrupt, CPU resource.
The indication of a change in a peripheral is referred to as an event, and is usually the same as
the interrupt conditions for that peripheral. Events are passed between peripherals using a dedi-
cated routing network called the Event Routing Network.
block diagram of the Event System with the Event Routing Network and the peripherals to which
it is connected. This highly flexible system can be used for simple routing of signals, pin func-
tions or for sequencing of events.
The maximum latency is two CPU clock cycles from when an event is generated in one periph-
eral, until the actions are triggered in one or more other peripherals.
The Event System is functional in both Active and Idle modes.
Inter-peripheral communication and signalling with minimum latency
CPU independent operation
4 Event Channels allow for up to 4 signals to be routed at the same time
100% predictable timing between peripherals
Events can be generated by
Events can be used by
The same event can be used by multiple peripherals for synchronized timing
Advanced Features
Functiond in Active and Idle mode
– TImer/Counters (TCxn)
– Real Time Counter (RTC)
– Analog to Digital Converter (ADCx)
– Analog Comparator (ACx)
– Ports (PORTx)
– System Clock (Clk
– Software (CPU)
– TImer/Counters (TCxn)
– Analog to Digital Converter (ADCx)
– Ports (PORTx)
– IR Communication Module (IRCOM)
– Manual Event Generation from software (CPU)
– Quadrature Decoding
– Digital Filtering
SYS
)
Figure 8-1 on page 16
XMEGA D4
shows a basic
15