ATxmega32D4 Atmel Corporation, ATxmega32D4 Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATxmega32D4
Manufacturer Part Number
ATxmega32D4
Description
Manufacturer
Atmel Corporation
Specifications of ATxmega32D4
Flash (kbytes)
32 Kbytes
Pin Count
44
Max. Operating Frequency
32 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
34
Ext Interrupts
34
Usb Speed
No
Usb Interface
No
Spi
4
Twi (i2c)
2
Uart
2
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
12
Adc Resolution (bits)
12
Adc Speed (ksps)
200
Analog Comparators
2
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
4
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.6 to 3.6
Operating Voltage (vcc)
1.6 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
4
Output Compare Channels
14
Input Capture Channels
14
Pwm Channels
14
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATxmega32D4-AU
Manufacturer:
Atmel
Quantity:
123
Part Number:
ATxmega32D4-AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATxmega32D4-CU
Manufacturer:
Maxim
Quantity:
71
Company:
Part Number:
ATxmega32D4-MH
Manufacturer:
Atmel
Quantity:
1 910
Company:
Part Number:
ATxmega32D4-MH
Manufacturer:
Atmel
Quantity:
1 704
Part Number:
ATxmega32D4-MH
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
8. Event System
8.1
8.2
8135J–AVR–12/10
Features
Overview
•
•
•
•
•
•
•
•
•
The Event System is a set of features for inter-peripheral communication. It enables the possibil-
ity for a change of state in one peripheral to automatically trigger actions in other peripherals.
The change of state in a peripheral that will trigger actions in other peripherals is configurable in
software. It is a simple, but powerful system as it allows for autonomous control of peripherals
without any use of interrupt, CPU resource.
The indication of a change in a peripheral is referred to as an event, and is usually the same as
the interrupt conditions for that peripheral. Events are passed between peripherals using a dedi-
cated routing network called the Event Routing Network.
block diagram of the Event System with the Event Routing Network and the peripherals to which
it is connected. This highly flexible system can be used for simple routing of signals, pin func-
tions or for sequencing of events.
The maximum latency is two CPU clock cycles from when an event is generated in one periph-
eral, until the actions are triggered in one or more other peripherals.
The Event System is functional in both Active and Idle modes.
Inter-peripheral communication and signalling with minimum latency
CPU independent operation
4 Event Channels allow for up to 4 signals to be routed at the same time
100% predictable timing between peripherals
Events can be generated by
Events can be used by
The same event can be used by multiple peripherals for synchronized timing
Advanced Features
Functiond in Active and Idle mode
– TImer/Counters (TCxn)
– Real Time Counter (RTC)
– Analog to Digital Converter (ADCx)
– Analog Comparator (ACx)
– Ports (PORTx)
– System Clock (Clk
– Software (CPU)
– TImer/Counters (TCxn)
– Analog to Digital Converter (ADCx)
– Ports (PORTx)
– IR Communication Module (IRCOM)
– Manual Event Generation from software (CPU)
– Quadrature Decoding
– Digital Filtering
SYS
)
Figure 8-1 on page 16
XMEGA D4
shows a basic
15