ATxmega32D4 Atmel Corporation, ATxmega32D4 Datasheet - Page 23
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATxmega32D4
Manufacturer Part Number
ATxmega32D4
Description
Manufacturer
Atmel Corporation
Specifications of ATxmega32D4
Flash (kbytes)
32 Kbytes
Pin Count
44
Max. Operating Frequency
32 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
34
Ext Interrupts
34
Usb Speed
No
Usb Interface
No
Spi
4
Twi (i2c)
2
Uart
2
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
12
Adc Resolution (bits)
12
Adc Speed (ksps)
200
Analog Comparators
2
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
4
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.6 to 3.6
Operating Voltage (vcc)
1.6 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
4
Output Compare Channels
14
Input Capture Channels
14
Pwm Channels
14
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATxmega32D4-AU
Manufacturer:
Atmel
Quantity:
123
Part Number:
ATxmega32D4-AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATxmega32D4-CU
Manufacturer:
Maxim
Quantity:
71
Company:
Part Number:
ATxmega32D4-MH
Manufacturer:
Atmel
Quantity:
1 910
Company:
Part Number:
ATxmega32D4-MH
Manufacturer:
Atmel
Quantity:
1 704
Part Number:
ATxmega32D4-MH
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
11.3.5
11.3.6
12. WDT - Watchdog Timer
12.1
12.2
8135J–AVR–12/10
Features
Overview
PDI reset
Software reset
The MCU can be reset through the Program and Debug Interface (PDI).
The MCU can be reset by the CPU writing to a special I/O register through a timed sequence.
•
•
•
•
The XMEGA D4 has a Watchdog Timer (WDT). The WDT will run continuously when turned on
and if the Watchdog Timer is not reset within a software configurable time-out period, the micro-
controller will be reset. The Watchdog Reset (WDR) instruction must be run by software to reset
the WDT, and prevent microcontroller reset.
The WDT has a Window mode. In this mode the WDR instruction must be run within a specified
period called a window. Application software can set the minimum and maximum limits for this
window. If the WDR instruction is not executed inside the window limits, the microcontroller will
be reset.
A protection mechanism using a timed write sequence is implemented in order to prevent
unwanted enabling, disabling or change of WDT settings.
For maximum safety, the WDT also has an Always-on mode. This mode is enabled by program-
ming a fuse. In Always-on mode, application software can not disable the WDT.
11 selectable timeout periods, from 8 ms to 8s.
Two operation modes
Runs from the 1 kHz output of the 32 kHz Ultra Low Power oscillator
Configuration lock to prevent unwanted changes
– Standard mode
– Window mode
XMEGA D4
23