SAM3S2A Atmel Corporation, SAM3S2A Datasheet - Page 941
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
SAM3S2A
Manufacturer Part Number
SAM3S2A
Description
Manufacturer
Atmel Corporation
Specifications of SAM3S2A
Flash (kbytes)
128 Kbytes
Pin Count
48
Max. Operating Frequency
64 MHz
Cpu
Cortex-M3
# Of Touch Channels
17
Hardware Qtouch Acquisition
No
Max I/o Pins
47
Ext Interrupts
47
Usb Transceiver
1
Quadrature Decoder Channels
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
2
Twi (i2c)
2
Uart
3
Ssc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
12
Adc Speed (ksps)
1000
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
32
Self Program Memory
YES
Dram Memory
No
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
- Current page: 941 of 1118
- Download datasheet (24Mb)
37.6.3.1
37.6.3.2
37.6.3.3
37.6.3.4
37.6.3.5
6500C–ATARM–8-Feb-11
Not Powered State
Entering Attached State
From Powered State to Default State
From Default State to Address State
From Address State to Configured State
Self powered devices can detect 5V VBUS using a PIO as described in the typical connection
section. When the device is not connected to a host, device power consumption can be reduced
by disabling MCK for the UDP, disabling UDPCK and disabling the transceiver. DDP and DDM
lines are pulled down by 330 KΩ resistors.
To enable integrated pull-up, the PUON bit in the UDP_TXVC register must be set.
Warning: To write to the UDP_TXVC register, MCK clock must be enabled on the UDP. This is
done in the Power Management Controller.
After pull-up connection, the device enters the powered state. In this state, the UDPCK and
MCK must be enabled in the Power Management Controller. The transceiver can remain
disabled.
After its connection to a USB host, the USB device waits for an end-of-bus reset. The unmask-
able flag ENDBUSRES is set in the register UDP_ISR and an interrupt is triggered.
Once the ENDBUSRES interrupt has been triggered, the device enters Default State. In this
state, the UDP software must:
In this state UDPCK and MCK must be enabled.
Warning: Each time an ENDBUSRES interrupt is triggered, the Interrupt Mask Register and
UDP_CSR registers have been reset.
After a set address standard device request, the USB host peripheral enters the address state.
Warning: Before the device enters in address state, it must achieve the Status IN transaction of
the control transfer, i.e., the UDP device sets its new address once the TXCOMP flag in the
UDP_CSR[0] register has been received and cleared.
To move to address state, the driver software sets the FADDEN flag in the UDP_GLB_STAT
register, sets its new address, and sets the FEN bit in the UDP_FADDR register.
Once a valid Set Configuration standard request has been received and acknowledged, the
device enables endpoints corresponding to the current configuration. This is done by setting the
EPEDS and EPTYPE fields in the UDP_CSRx registers and, optionally, enabling corresponding
interrupts in the UDP_IER register.
• Enable the default endpoint, setting the EPEDS flag in the UDP_CSR[0] register and,
• Configure the interrupt mask register which has been reset by the USB reset detection
• Enable the transceiver clearing the TXVDIS flag in the UDP_TXVC register.
optionally, enabling the interrupt for endpoint 0 by writing 1 to the UDP_IER register. The
enumeration then begins by a control transfer.
SAM3S
941
Related parts for SAM3S2A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![SAM3S](/images/no-image3.png)
Part Number:
Description:
ARM-based Flash MCU
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
![U641B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
![U4082B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
![U4255BM-M](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B-P](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
![TDA4470](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
![ATF22V10B-25PC](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
![AT89C51ED2-IM](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
![AT24C01](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: