AD7934-6 Analog Devices, AD7934-6 Datasheet - Page 19
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD7934-6
Manufacturer Part Number
AD7934-6
Description
4-Channel, 625 kSPS, 12-Bit Parallel ADC with a Sequencer
Manufacturer
Analog Devices
Datasheet
1.AD7934-6.pdf
(28 pages)
Specifications of AD7934-6
Resolution (bits)
12bit
# Chan
4
Sample Rate
625kSPS
Interface
Par
Analog Input Type
Diff-Uni,SE-Uni
Ain Range
Uni (Vref),Uni (Vref) x 2
Adc Architecture
SAR
Pkg Type
SOP
Another method of driving the AD7934-6 is to use the
differential amplifier. The AD8138 can be used as a single-
ended-to-differential amplifier or as a differential-to-differential
amplifier. The device is as easy to use as an op amp and greatly
simplifies differential signal amplification and driving.
Pseudo Differential Mode
The AD7934-6 can have two pseudo differential pairs by setting
the MODE0 and MODE1 bits in the control register to 1 and 0,
respectively. V
have an amplitude of V
chosen) to make use of the full dynamic range of the part. A dc
input is applied to the V
provides an offset from ground or a pseudo ground for the
V
The benefit of pseudo differential inputs is that they separate the
analog input signal ground from the ADC ground, allowing dc
common-mode voltages to be cancelled. Typically, the voltage
range for the V
extend from −0.3 V to +0.7 V when V
+1.8 V when V
for the pseudo differential mode.
GND
V
GND
REF
Figure 28. Dual Op Amp Circuit to Convert a Single-Ended Unipolar Signal
IN
Figure 27. Dual Op Amp Circuit to Convert a Single-Ended Bipolar Signal
+ input.
2 × V
V
REF
REF
p-p
p-p
220Ω
440Ω
20kΩ
440Ω
IN
IN−
DD
+ is connected to the signal source, which must
A
A
= 5 V. Figure 29 shows a connection diagram
pin while in pseudo differential mode can
into a Differential Unipolar Signal
220Ω
220Ω
220Ω
220Ω
220Ω
220Ω
into a Differential Signal
+
REF
10kΩ
IN−
10kΩ
V+
V–
V+
V–
V+
V–
V+
V–
(or 2 × V
pin. The voltage applied to this input
27Ω
27Ω
27Ω
27Ω
REF
DD
depending on the range
= 3 V, or from −0.3 V to
3.75V
2.5V
1.25V
3.75V
2.5V
1.25V
3.75V
2.5V
1.25V
3.75V
2.5V
1.25V
V
V
V
V
AD7934-6
AD7934-6
IN+
IN–
IN+
IN–
0.47µF
0.47µF
AD8138
V
V
REF
REF
Rev. B | Page 19 of 28
ANALOG INPUT SELECTION
As shown in Table 9, users can set up their analog input con-
figuration by setting the values in the MODE0 and MODE1 bits
in the control register. Assuming the configuration has been
chosen, there are two different ways of selecting the analog
input to be converted, depending on the state of the SEQ0 and
SEQ1 bits in the control register.
Traditional Multichannel Operation (SEQ0 = SEQ1 = 0)
Any one of four analog input channels or two pairs of channels
can be selected for conversion in any order by setting the SEQ0
and SEQ1 bits in the control register to 0. The channel to be
converted is selected by writing to the address bits, ADD1 and
ADD0, in the control register to program the multiplexer prior to
the conversion. This mode of operation is that of a traditional
multichannel ADC, where each data write selects the next
channel for conversion. Figure 30 shows a flowchart of this mode
of operation. The channel configurations are shown in Table 9.
Using the Sequencer: Consecutive Sequence
(SEQ0 = SEQ1 = 1)
A sequence of consecutive channels can be converted beginning
with Channel 0, and ending with a final channel selected by
writing to the ADD1 and ADD0 bits in the control register. This
is done by setting the SEQ0 and SEQ1 bits in the control
register to 1. In this mode, once the control register is written
to, the next conversion is on Channel 0, then Channel 1, and so
on, until the channel selected by the address bits (ADD1 and
ADD0) is reached.
*ADDITIONAL PINS OMITTED FOR CLARITY.
V
REF
Figure 29. Pseudo Differential Mode Connection Diagram
Figure 30. Traditional Multichannel Operation Flow Chart
ISSUE CONVST PULSE TO INITIATE A CONVERSION
IN THE CONTROL REGISTER. SET SEQ0 = SEQ1 = 0.
CHANGING THE VALUES OF BITS ADD2 TO ADD0
p-p
INITIATE A WRITE CYCLE TO SELECT THE NEXT
CHANNEL TO CONVERT ON (ADD1 TO ADD0).
INITIATE A READ CYCLE TO READ THE DATA
SET SEQ0 = SEQ1 = 0. SELECT THE DESIRED
SET UP OPERATING MODE, ANALOG INPUT,
WRITE TO THE CONTROL REGISTER TO
CHANNEL TO BE CONVERTED ON BY
FROM THE SELECTED CHANNEL.
AND OUTPUT CONFIGURATION.
ON THE SELECTED CHANNEL.
POWER ON
VOLTAGE
DC INPUT
V
V
V
REF
IN+
IN–
AD7934-6*
+
0.47µF
AD7934-6