ADCMP601BKSZ-REEL7 Analog Devices Inc, ADCMP601BKSZ-REEL7 Datasheet - Page 5

• Manufacturer Part Number: ADCMP601BKSZ-REEL7
• Description: IC COMP TTL/CMOS 1CHAN SC70-6
• Manufacturer: Analog Devices Inc
• Type: with Latchr

Specifications of ADCMP601BKSZ-REEL7

• Number Of Elements: 1
• Output Type: CMOS, TTL
• Voltage - Supply: 2.5 V ~ 5.5 V
• Mounting Type: Surface Mount
• Package / Case: 6-TSSOP, SC-88, SOT-363
• Comparator Type: High Speed
• No. Of Comparators: 1
• Response Time: 3.5ns
• Ic Output Type: CMOS, MOS, Open-Collector / Drain, TTL
• Supply Current: 3.5mA
• Supply Voltage Range: 2.5V To 5.5V
• Rohs Compliant: Yes
• Number Of Elements: 1
• Technology: CMOS
• Input Offset Voltage: 5mV
• Input Bias Current (typ): 5uA
• Single Supply Voltage (typ): 3/5V
• Dual Supply Voltage (typ): Not RequiredV
• Supply Current (max): 4@5.5VmA
• Power Supply Requirement: Single
• Common Mode Rejection Ratio: 50dB
• Voltage Gain In Db: 85dB
• Power Supply Rejection Ratio: 50dB
• Single Supply Voltage (min): 2.5V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Dissipation: 23mW
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 6
• Package Type: SC-70
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ADCMP601BKSZ-REEL7TR

TIMING INFORMATION
Figure 2 illustrates the ADCMP600/ADCMP601/ADCMP602 latch timing relationships. Table 2 provides definitions of the terms shown
in Figure 2.
Table 2. Timing Descriptions
Symbol
t
t
t
t
t
t
t
t
t
V
PDH
PDL
PLOH
PLOL
H
PL
S
R
F
OD
Timing
Input to output high delay
Input to output low delay
Latch enable to output high delay
Latch enable to output low delay
Minimum hold time
Minimum latch enable pulse width
Minimum setup time
Output rise time
Output fall time
Voltage overdrive
INPUT VOLTAGE
LATCH ENABLE
DIFFERENTIAL
Q OUTPUT
V
IN
Description
Propagation delay measured from the time the input signal crosses the reference (± the
input offset voltage) to the 50% point of an output low-to-high transition.
Propagation delay measured from the time the input signal crosses the reference (± the
input offset voltage) to the 50% point of an output high-to-low transition.
Propagation delay measured from the 50% point of the latch enable signal low-to-high
transition to the 50% point of an output low-to-high transition.
Propagation delay measured from the 50% point of the latch enable signal low-to-high
transition to the 50% point of an output high-to-low transition.
Minimum time after the negative transition of the latch enable signal that the input signal
must remain unchanged to be acquired and held at the outputs.
Minimum time that the latch enable signal must be high to acquire an input signal change.
Minimum time before the negative transition of the latch enable signal occurs that an
input signal change must be present to be acquired and held at the outputs.
Amount of time required to transition from a low to a high output as measured at the 20%
and 80% points.
Amount of time required to transition from a high to a low output as measured at the 20%
and 80% points.
Difference between the input voltages V
Figure 2. System Timing Diagram
V
t
S
OD
t
PDL
Rev. A | Page 5 of 16
t
H
t
F
ADCMP600/ADCMP601/ADCMP602
t
PL
t
PLOH
A
and V
B
.
1.1V
V
50%
N
± V
OS