1600636-6 TE Connectivity, 1600636-6 Datasheet

1600636-6

Manufacturer Part Number
1600636-6
Description
Manufacturer
TE Connectivity
Datasheets
1.1-1600636-0.pdf (5 pages)
2.1-1600636-5.pdf (9 pages)

Specifications of 1600636-6

Product Series
XL
Connector Type
Connector Assembly
Termination Style
Panel
Mating Type
Blindmate
Guides
With
Mating Functionality
Mate First-Break Last
Voltage Rating (signal) (vac)
60
Voltage Rating (power) (vac)
300
Voltage Rating (power) (vdc)
200
Sequencing
Yes
Connector Configuration Orientation
Right-to-Left
Centerline, Dc Module (mm [in])
6.35 [0.250]
Centerline, Ac Module (mm [in])
7.62 [0.300]
Centerline, Matrix (mm [in])
2.54 x 2.54 [.100 x .100]
Contact Type
Socket
Connector Style
Receptacle
Housing Material
Thermoplastic - GF
Total Number Of Dc Power
12
Total Number Of Ac Power
4
Total Number Of Signal
24
Connector Contact Configuration (no. Of Pos./type)
4/AC Power, 24/Signal, 12/DC Power
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Not relevant for lead free process
Rohs/elv Compliance History
Always was RoHS compliant
Application Use
Cable-to-Board
|
|
1.
1.1.
1.2.
1.3.
2.
2.1.
2.2.
3.
3.1.
3.2.
©2006 Tyco Electronics Corporation
Harrisburg, PA
All International Rights Reserved.
SCOPE
Content
This specification covers performance, tests and quality requirements for the Tyco Electronics Multi-
Beam XL* Cable Panel Mount and Squeeze-To-Release Receptacles.
Qualification
When tests are performed on the subject product line, procedures specified in Figure 3 shall be used.
All inspections shall be performed using the applicable inspection plan and product drawing.
Qualification Test Results
Successful qualification testing on the subject product line was completed on 02Dec04. The
Qualification Test Report number for this testing is 501-597. This documentation is on file at and
available from Engineering Practices and Standards (EPS).
Additional testing on part number 1874902-1 using 12 AWG wire on 3 adjacent contacts and .300 pitch
at 28 amperes was performed by TUV. The project number for this testing is S1600403-101.
APPLICABLE DOCUMENTS
The following documents form a part of this specification to the extent specified herein. Unless
otherwise specified, the latest edition of the document applies. In the event of conflict between the
requirements of this specification and the product drawing, the product drawing shall take precedence.
In the event of conflict between the requirements of this specification and the referenced documents,
this specification shall take precedence.
Tyco Electronics Documents
!
!
!
Industry Standard
EIA-364: Electrical Connector/Socket Test Procedures Including Environmental Classifications
REQUIREMENTS
Design and Construction
Product shall be of the design, construction and physical dimensions specified on the applicable
product drawing.
Materials
Materials used in the construction of this product shall be as specified on the applicable product
drawing.
109-197: Test Specification (AMP Test Specifications vs EIA and IEC Test Methods)
114-13112: Application Specification (Multi-Beam XL Cable Receptacle Assemblies)
501-597: Qualification Test Report (Multi-Beam XL* Cable Panel Mount and
Squeeze-To-Release Receptacles)
Product
Specification
Multi-Beam XL* Cable Panel Mount and Squeeze-To-Release
Receptacles
* Trademark
| Indicates change
For latest revision, visit our website at www.tycoelectronics.com\documents.
For Regional Customer Service, visit our website at www.tycoelectronics.com
108-2157
05Apr06 Rev C
1 of 9
LOC B

Related parts for 1600636-6

Image
Part Number
Description
Manufacturer
Datasheet
Request R
160063-1
Part Number:
160063-1
Description:
Manufacturer:
TE Connectivity
160063-2
Part Number:
160063-2
Description:
Manufacturer:
TE Connectivity
TE-PRINTER-PERFORATOR
Part Number:
TE-PRINTER-PERFORATOR
Description:
Printers THERMAL PRINTER HS-SLEEVE MARKER
Manufacturer:
TE Connectivity
120658-2
Part Number:
120658-2
Description:
Manufacturer:
TE Connectivity
Datasheet:
120658-2.pdf (1 page)
120661-1
Part Number:
120661-1
Description:
Manufacturer:
TE Connectivity
Datasheet:
120661-1.pdf (1 page)
120661-2
Part Number:
120661-2
Description:
Manufacturer:
TE Connectivity
Datasheet:
120661-1.pdf (1 page)
120662-1
Part Number:
120662-1
Description:
Manufacturer:
TE Connectivity
Datasheet:
120662-1.pdf (1 page)
120663-1
Part Number:
120663-1
Description:
Manufacturer:
TE Connectivity
Datasheet:
120663-1.pdf (1 page)
120664-1
Part Number:
120664-1
Description:
Manufacturer:
TE Connectivity
Datasheet:
120664-1.pdf (1 page)
120670-1
Part Number:
120670-1
Description:
Manufacturer:
TE Connectivity
Datasheet:
120670-1.pdf (1 page)
280388-2
Part Number:
280388-2
Description:
Manufacturer:
TE Connectivity
Datasheet:
280388-2.pdf (1 page)
1-826632-7
Part Number:
1-826632-7
Description:
Manufacturer:
TE Connectivity
Datasheet:
1-826632-1.pdf (1 page)
280375-1
Part Number:
280375-1
Description:
Manufacturer:
TE Connectivity
Datasheet:
280370-3.pdf (1 page)
3-826947-6
Part Number:
3-826947-6
Description:
Manufacturer:
TE Connectivity
Datasheet:
1-826947-1.pdf (1 page)
5-826953-0
Part Number:
5-826953-0
Description:
Manufacturer:
TE Connectivity
Datasheet:
1-826953-9.pdf (1 page)

1600636-6 Summary of contents

Page 1

Product Specification Multi-Beam XL* Cable Panel Mount and Squeeze-To-Release Receptacles 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for the Tyco Electronics Multi- Beam XL* Cable Panel Mount and Squeeze-To-Release Receptacles. 1.2. Qualification When tests are ...

Page 2

Ratings Voltage: See Figure 1 ! Current: See Figure 2 ! Temperature: -20 to 105 ! Contact Type Signal .100 [2.54 mm] Power .200 [5.08 mm] Power .250 [6.35 mm] Power .300 [7.62 mm] Volts RMS (Safety Extra Low ...

Page 3

Test Description Contact resistance at rated current, power contacts. Insulation resistance. Withstanding voltage. Temperature rise vs current. Vibration, random. Mechanical shock. Durability. Mating force. Rev C Requirement 0.7 milliohm maximum, end of life. Wire Size Test Current (AWG) (amperes DC) ...

Page 4

Test Description Unmating force. Contact insertion force, power contacts. Contact retention, straight pull. Contact retention, angled pull. Housing lock strength, straight pull. 25 pounds minimum. Housing lock strength, angles pull. Rev C Requirement 8 ounce minimum per power contact. .7 ...

Page 5

Test Description Crimp tensile. Thermal shock. Humidity-temperature cycling. Temperature life. Mixed flowing gas. Shall meet visual requirements, show no physical damage, and meet requirements of additional NOTE tests as specified in the Product Qualification and Requalification Test Sequence shown in ...

Page 6

Product Qualification and Requalification Test Sequence Test or Examination Initial examination of product Low level contact resistance, signal and power contacts Low level contact resistance, power contacts only Contact resistance at rated current, power contacts Insulation resistance Withstanding voltage ...

Page 7

QUALITY ASSURANCE PROVISIONS 4.1. Qualification Testing A. Specimen Selection Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be selected at random from current production. Test group 1 shall consist of 6 mated pairs (panel mount ...

Page 8

Tolerance: Unless otherwise specified, ±.005 or ± 2 degrees as applicable. NOTE 2. Material: AISI Type 02 tool steel per Material Specification 100-15. 3. Heat Treat: Rockwell C50-55 4. Gage surface shall be clean of contaminates or lubricants. Rev ...

Page 9

Tolerance: Unless otherwise specified, ±.005 or ± 2 degrees as applicable. NOTE 2. Material: AISI Type 02 tool steel per Material Specification 100-15. 3. Heat Treat: Rockwell C50-55. Rev C Figure 6 Power Contact Tensile Test Clamp 108-2157 9 ...

Related keywords