ST72651AR6 STMicroelectronics, ST72651AR6 Datasheet - Page 35
ST72651AR6
Manufacturer Part Number
ST72651AR6
Description
LOW-POWER, FULL-SPEED USB 8-BIT MCU WITH 32K FLASH, 5K RAM, FLASH CARD I/F, TIMER, PWM, ADC, I2C, SPI
Manufacturer
STMicroelectronics
Datasheet
1.ST72651AR6.pdf
(161 pages)
Specifications of ST72651AR6
Dual Supply Management
analog voltage detector on the USB power line to enable smart power switching from USB power to battery (on E suffix devices).
Programmable Internal Voltage Regulator For Memory Cards (2.8v To 3.5v) Supplying
Flash Card I/O lines (voltage shifting)
5 Usb Endpoints
1 control endpoint
Dtc (data Transfer Coprocessor)
Universal Serial/Parallel communications interface, with software plug-ins for current and future protocol standards
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
POWER SUPPLY MANAGEMENT (Cont’d)
6.4.3 Storage Media Interface I/Os
The microcontroller is able to drive Storage Media
through an interface operating at a different volt-
age from the rest of the circuit.
This is achieved by powering the Storage Media
interface I/O circuitry through a specific supply rail
connected to V
either as an input or output.
If the on-chip voltage regulator is off, power to the
interface I/Os should be provided externally to the
V
Alone Mode, or in USB mode when the current re-
quired to power the Storage Media is above the
current capacity of the on-chip regulator.
If the on-chip voltage regulator is on, it powers the
interface I/Os, and V
age Media. This is recommended in USB Mode,
when the current required to power the Storage
Media is within the capacity of the on-chip regula-
tor.
Caution: If VDDF is supplied externally, the regu-
lator must not be enabled.
Important Note:
If V
be used and are tied to ground. Refer to
9.2.4
Application Example:
Stand-Alone Mode
– The Storage Media interface supply is powered
DDF
by V
nects V
any True Open Drain I/O pin and controlled by
user software.
DDF
for more details.
pin. This should be the case when in Stand-
DD
is not present, all V
enabled by an external switch which con-
DD
to V
DDF
DDF
pin. The V
. This switch can be driven by
DDF
pin can supply the Stor-
DDF
DDF
-driven I/Os cannot
pin can be used
Section
Doc ID 7215 Rev 4
– The on-chip voltage regulator must be disabled
USB Mode
– In this case the core of the microcontroller is run-
– The Storage Media Interface can be powered
– The regulator output voltage can be pro-
– Should the current requirement for the Storage
Caution: The user should ensure that V
not exceed the maximum rating specified for the
Storage Media V
AGE switch on.
to avoid any conflict and to decrease consump-
tion (reset the REGEN bit in the PCR register).
ning from the USB bus power or the self power
supply. V
a voltage from 4.0 to 5.5V.
through the on-chip regulator (providing power to
the I/O pins and output on pin V
requirement is within the output capacity of the
on chip regulator.
grammed to 2.8V, 3.3V, 3.4V or 3.5 Volts, de-
pending on the Storage Media specifications.
(see VSET[1:0] bits in PCR register description)
Media be higher than the current capacity of the
on chip regulator, an external regulator should be
used. Thus the on-chip voltage regulator must be
disabled to avoid any conflict (reset the REGEN
bit in the PCR register).
DD
and USBV
DDF
max when switching STOR-
DD
pins are supplied with
DDF
ST72651AR6
) if the current
DD
35/161
does
1