MC10E1652FNG ON Semiconductor, MC10E1652FNG Datasheet - Page 3

• Manufacturer Part Number: MC10E1652FNG
• Description: IC COMPARATOR DUAL ECL 20PLCC
• Manufacturer: ON Semiconductor
• Series: MOSAIC III™r
• Type: with Latchr

Specifications of MC10E1652FNG

• Number Of Elements: 2
• Output Type: Differential, ECL
• Mounting Type: Surface Mount
• Package / Case: 20-LCC (J-Lead)
• Number Of Channels: 2 Channels
• Product: Analog Comparators
• Response Time: 475 ps
• Supply Voltage (max): 5 V
• Supply Voltage (min): - 5.2 V
• Supply Current (max): 50 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• High Level Output Current: 150 uA
• Minimum Operating Temperature: 0 C
• Propagation Delay Time: 925 ps
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: MC10E1652FNGOS

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
1. Input V
2. Outputs are terminated through a 50 ohm resistor to GND−2 volts.
3. VCMR Min varies 1:1 with V
4. The HYS pin programming characterization information is shown in Figure 2. The hysteresis values indicated in the data sheet are for the
5. Hysteresis skew (V
Table 3. MAXIMUM RATINGS
Table 4. DC CHARACTERISTICS
VSUP
VPP
V
I
I
TA
T
q
q
V
T
V
V
V
V
II
I
I
I
VCMR
Hys
V
C
Symbol
Symbol
out
BB
IH
CC
EE
stg
JA
JC
sol
I
EE
OH
OL
IL
IH
skew
in
condition in which the voltage on the HYS pin is set to V
27 mV and the V
hysteresis window ranged from 14 mV below the reference level to 13 mV above the reference level. All hysteresis measurements were
determined using a reference voltage of 0 mV. The hysteresis skew values apply over the programming range shown in Figure 2.
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
IL
Output HIGH Voltage (Note 2)
Output Low Voltage (Note 2)
Input LOW Voltage (LEN)
Input HIGH Voltage (LEN)
Input Current (V1, V2)
Input HIGH Current (LEN)
Positive Supply Current
Negative Supply Current
Common Mode Range (Note 3)
Hysteresis (Note 4)
Hysteresis Skew (Note 5)
Input Capacitance
and V
Total Supply Voltage
Differential Input Voltage
Input Voltage
Output Current
V
Operating Temperature Range
Storage Temperature Range
Thermal Resistance (Junction to Ambient)
Thermal Resistance (Junction to Case)
Operating Range
Wave Solder
BB
Sink/Source
IH
skew
parameters vary 1:1 with V
skew
Characteristic
value indicates that the hysteresis was skewed from the reference level by 1 mV in the negative direction. Hence the
) is provided to indicate the offset of the hysteresis window. For example, at 25°C the nominal hysteresis value is
Parameter
EE
; Max varies 1:1 with V
V
CC
PLCC
= +5.0 V ±5%; V
DIP
CC
. Output V
−1020
−1950
−1.95
−1.17
−2.0
Min
CC
http://onsemi.com
Continuous
Surge
0 LFPM
500 LFPM
std bd
GND = 0 V
v 3 sec @ 248°C
.
EE
OH
EE
−1.0
.
Typ
0°C
27
|V
Condition 1
and V
= −5.2 V ±5%, V
|V1 − V2|
EE
| + |V
3
−1630
−1.48
−0.84
OL
−840
Max
150
−55
3.0
65
50
3
2
CC
parameters vary 1:1 with GND.
|
−1950
−1.95
−1.13
−980
−2.0
Min
CC
28 PLCC
28 PLCC
28 PLCC
= 0 V (Note 1)
Condition 2
25°C
−1.0
Typ
27
−1630
−1.48
−0.81
−810
Max
150
−55
3.0
65
50
3
2
−1950
−1.95
−1.07
−920
−2.0
Min
V
EE
−65 to +150
−4.2 to −5.7
0 to +85
22 to 26
v V
Rating
± 0.5
12.0
63.5
43.5
85°C
Typ
100
265
3.7
50
30
0
I
v V
−0.735
−1600
CC
−1.45
−735
Max
150
−55
3.0
65
50
3
2
Units
°C/W
°C/W
°C/W
mA
mA
mA
°C
°C
°C
Unit
V
V
V
V
mV
mV
mV
mV
mA
mV
mV
mA
pF
V