SP202EEN Exar Corporation, SP202EEN Datasheet
SP202EEN
Available stocks
Related parts for SP202EEN
SP202EEN Summary of contents
Page 1
Operates from Single +5V Power Supply Meets All RS-232D and ITU V.28 Specifications Operates with 0.1µF to 10µF Capacitors High Data Rate – 120Kbps Under Load Low Power Shutdown ≤1µA (Typical) 3-State TTL/CMOS Receiver Outputs Low Power CMOS – ...
Page 2
This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods ...
Page 3
Load Current ...
Page 4
FEATURES… The SP202E/232E/233E/310E/312E devices are a family of line driver and receiver pairs that meet the specifications of RS-232 and V.28 serial protocols with enhanced ESD perfor- mance. The ESD tolerance has been improved on these devices to over ±15KV ...
Page 5
Figure 2. Typical Circuits using the SP233ECP and SP233ECT The instantaneous slew rate of the transmitter output is internally limited to a maximum of 30V/ µs in order to meet the standards [EIA RS-232-D 2.1.7, Paragraph (5)]. However, the transition ...
Page 6
C 1 Figure 4. Charge Pump — Phase 1 In actual system applications quite possible for signals to be applied to the receiver inputs before power is applied to the receiver circuitry. This occurs, for example, when a ...
Page 7
C 2 GND GND – –10V Figure 6. Charge Pump Waveforms be symmetrical. Older charge pump approaches – + that generate V from V will show a decrease in – the magnitude of V ...
Page 8
SP310E transmitter and receiver outputs in a high impedance condition (tri-stated). The shutdown mode is controlled on the SP312E by a logic “0” on the SHUTDOWN control line (pin 18); this also puts the transmitter outputs in a tri–state mode. ...
Page 9
Power Source Figure 9. ESD Test Circuit for Human Body Model with IEC1000-4-2 is that the system is required to withstand an amount of static electricity when ESD is applied to points and surfaces of ...
Page 10
Figure 11. ESD Test Waveform for IEC1000-4-2 discharge current rather than the discharge voltage. Variables with an air discharge such as approach speed of the object carrying the ESD potential to the system and humidity ...
Page 11
INDEX AREA PIN SSOP Dimensions in (mm) JEDEC MO-150 (AE) Variation MIN 1.65 b 0.22 c 0.09 D 6.90 E 7.40 E1 5.00 L 0.55 ...
Page 12
D e E/2 1 INDEX AREA (D/2 X E1/2) TOP VIEW b WITH PLATING c BASE METAL SECTION B SIDE VIEW Date: 7/19/ E1 Ø1 Seating Plane Ø1 Seating Plane SP202E Series ...
Page 13
D E INDEX AREA (D/2 X E1/2) e TOP VIEW b WITH PLATING c BASE METAL SECTION B SIDE VIEW Date: 7/19/ E1/2 b Seating Plane Seating Plane SP202E Series ...
Page 14
PIN PDIP Dimensions in inches JEDEC MS-001 (AC) Variation MIN A .015 A1 A2 .115 b .014 b2 .045 b3 .030 c .008 D .880 D1 .005 E .300 E1 .240 ...
Page 15
... SP202ECT.............................0°C to +70°C.................................SP202ECT.........................................................................16–pin WSOIC SP202ECT/TR.......................0°C to +70°C.................................SP202ECT.........................................................................16–pin WSOIC SP202EEN..........................–40°C to +85°C................................SP202EEN.........................................................................16–pin NSOIC SP202EEN/TR....................–40°C to +85°C................................SP202EEN.........................................................................16–pin NSOIC SP202EEP..........................–40°C to +85°C................................SP202EEP.........................................................................16–pin PDIP SP202EET..........................–40°C to +85°C................................SP202EET..........................................................................16–pin WSOIC SP202EET/TR.....................– ...