PIC16F819 Microchip Technology Inc., PIC16F819 Datasheet - Page 87
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
PIC16F819
Manufacturer Part Number
PIC16F819
Description
18/20-pin Enhanced Flash Microcontrollers With Nanowatt Technology
Manufacturer
Microchip Technology Inc.
Datasheet
1.PIC16F819.pdf
(176 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16F819
Manufacturer:
MIC
Quantity:
699
Part Number:
PIC16F819-1/P
Manufacturer:
MIC
Quantity:
20 000
Company:
Part Number:
PIC16F819-E/SO
Manufacturer:
ZETTLER
Quantity:
201
Company:
Part Number:
PIC16F819-E/SS
Manufacturer:
MICROCHIP
Quantity:
12 000
Company:
Part Number:
PIC16F819-E/SS
Manufacturer:
Microchip Technology
Quantity:
135
Company:
Part Number:
PIC16F819-I/P
Manufacturer:
MICROCHIP
Quantity:
1 000
Part Number:
PIC16F819-I/SS
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
11.2
The A/D conversion time per bit is defined as T
A/D conversion requires 9.0 T
The source of the A/D conversion clock is software
selectable. The seven possible options for T
• 2 T
• 4 T
• 8 T
• 16 T
• 32 T
• 64 T
• Internal A/D module RC oscillator (2-6 s)
For correct A/D conversions, the A/D conversion clock
(T
as small as possible, but no less than 1.6 s and not
greater than 6.4 s.
Table 11-1 shows the resultant T
the device operating frequencies and the A/D clock
source selected.
TABLE 11-1:
2003 Microchip Technology Inc.
Note 1:
AD
) must be selected to ensure a minimum T
OSC
OSC
OSC
OSC
OSC
OSC
2:
3:
Operation
RC
16 T
32 T
64 T
Selecting the A/D Conversion
Clock
2 T
4 T
8 T
The RC source has a typical T
When the device frequencies are greater than 1 MHz, the RC A/D conversion clock source is only
recommended for Sleep operation.
For extended voltage devices (LF), please refer to Section 15.0 “Electrical Characteristics”.
(1,2,3)
OSC
OSC
OSC
OSC
OSC
OSC
T
AD
vs. MAXIMUM DEVICE OPERATING FREQUENCIES (STANDARD DEVICES (F))
AD Clock Source (T
AD
AD
per 10-bit conversion.
ADCS<2>
times derived from
0
1
0
1
0
1
X
AD
AD
time of 4 s but can vary between 2-6 s.
AD
are:
AD
. The
time
AD
)
ADCS<1:0>
11.3
The ADCON1 and TRISA registers control the opera-
tion of the A/D port pins. The port pins that are desired
as analog inputs must have their corresponding TRIS
bits set (input). If the TRIS bit is cleared (output), the
digital output level (V
The A/D operation is independent of the state of the
CHS<2:0> bits and the TRIS bits.
Note 1: When reading the Port register, all pins
00
00
01
01
10
10
11
2: Analog levels on any pin that is defined as
Configuring Analog Port Pins
configured as analog input channels will
read as cleared (a low level). Pins config-
ured as digital inputs will convert an
analog input. Analog levels on a digitally
configured input will not affect the
conversion accuracy.
a digital input (including the AN4:AN0
pins) may cause the input buffer to
consume current out of the device
specification.
PIC16F818/819
OH
Maximum Device Frequency
or V
OL
) will be converted.
1.25 MHz
2.5 MHz
(Note 1)
10 MHz
20 MHz
20 MHz
5 MHz
DS39598D-page 85