HT46R64 Holtek Semiconductor Inc., HT46R64 Datasheet - Page 4

• Manufacturer Part Number: HT46R64
• Description: Ht46r64/ht46c64 -- A/d With Lcd Type 8-bit Mcu
• Manufacturer: Holtek Semiconductor Inc.

Pin Description
Absolute Maximum Ratings
Supply Voltage ...........................V
Input Voltage..............................V
Note: These are stress ratings only. Stresses exceeding the range specified under Absolute Maximum Ratings may
Rev. 1.80
PA0/BZ
PA1/BZ
PA2
PA3/PFD
PA4~PA7
PB0/AN0
PB1/AN1
PB2/AN2
PB3/AN3
PB4/AN4
PB5/AN5
PB6/AN6
PB7/AN7
PD0/PWM0
PD1/PWM1
PD2/PWM2
PD3/PWM3
PD4/INT0
PD5/INT1
PD6/TMR0
PD7/TMR1
VSS
VLCD
VMAX
V1, V2, C1, C2
COM0~COM2
COM3/SEG32
SEG0~SEG31
OSC1
OSC2
OSC3
OSC4
VDD
RES
Pin Name
cause substantial damage to the device. Functional operation of this device at other conditions beyond those
listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliabil-
ity.
I/O
I/O
I/O
I/O
I/O
O
O
O
O
I
I
I
I
I
I
1/3 or 1/4 Duty
Logical Output
Crystal or RC
System Clock
Wake-up
Options
Pull-high
Pull-high
Pull-high
Pull-high
RTC or
Buzzer
PWM
PFD
SS
SS
0.3V to V
0.3V to V
Bidirectional 8-bit input/output port. Each bit can be configured as wake-up in-
put by option. Software instructions determine the CMOS output or Schmitt
Trigger input with or without pull-high resistor (determined by pull-high op-
tions: bit option). The BZ, BZ and PFD are pin-shared with PA0, PA1 and
PA3, respectively.
Bidirectional 8-bit input/output port. Software instructions determine the
CMOS output, Schmitt trigger input with or without pull-high resistor (deter-
mined by pull-high option: bit option) or A/D input. Once a PB line is selected
as an A/D input (by using software control), the I/O function and pull-high re-
sistor are disabled automatically.
Bidirectional 4-bit input/output port. Software instructions determine the
CMOS output, Schmitt trigger input with or without a pull-high resistor (deter-
mined by pull-high option: bit option). The PWM0/PWM1/PWM2/PWM3 out-
put function are pin-shared with PD0/PD1/PD2/PD3 (dependent on PWM
options).
Bidirectional 4-bit input/output port. Software instructions determine the
CMOS output, Schmitt trigger input with or without a pull-high resistor (deter-
mined by pull-high option: bit option). The INT0, INT1, TMR0 and TMR1 are
pin-shared with PD4/PD5/PD6/PD7.
Negative power supply, ground
LCD power supply
IC maximum voltage connect to VDD, VLCD or V1
Voltage pump
SEG32 can be set as a segment or as a common output driver for LCD panel
by options. COM0~COM2 are outputs for LCD panel plate.
LCD driver outputs for LCD panel segments. SEG0~SEG23 can be optioned
as logical outputs.
OSC1 and OSC2 are connected to an RC network or a crystal (by options) for
the internal system clock. In the case of RC operation, OSC2 is the output ter-
minal for 1/4 system clock. The system clock may come from the RTC oscilla-
tor. If the system clock comes from RTCOSC, these two pins can be floating.
Real time clock oscillators. OSC3 and OSC4 are connected to a 32768Hz
crystal oscillator for timing purposes or to a system clock source (depending
on the options). No built-in capacitor
Positive power supply
Schmitt trigger reset input, active low
DD
SS
+6.0V
+0.3V
4
Storage Temperature ............................ 50 C to 125 C
Operating Temperature........................... 40 C to 85 C
Description
HT46R64/HT46C64
February 14, 2006