ZY8105 Power-One, ZY8105 Datasheet - Page 20

• Manufacturer Part Number: ZY8105
• Description: Zy8105 5a Dc-dc Intelligent Pol
• Manufacturer: Power-One

8.3.4.1
Z-Series POLs can be arranged in several groups to
simplify fault management.
defined as a number of POLs with interconnected
OK pins. A group can include from 1 to 32 POLs. If
fault propagation within a group is desired, the
propagation bit needs to be checked in the GUI Fault
Management Window. The parameters can also be
programmed directly via the I
the PC3 register shown in Figure 33.
When propagation is enabled, the faulty POL pulls its
OK pin low. A low OK line initiates turn-off of other
POLs in the group.
In addition, the OK lines can be connected to the
DPM to facilitate propagation of faults and errors
between groups.
independent groups.
between groups, the respective bit needs to be
checked in the GUI Fault and Error Propagation
window shown in Figure 34.
ZD-01740 Rev. 1.0
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
R/W-0
PTM
Bit 7
Figure 33. Protection Configuration Register PC3
PTM : Temperature warning Message
1 = enabled
0 = disabled
PGM: Powe
1 = enabled
0 = disabled
TRP : Tracking fault propagation
1 = enabled
0 = disabled
OTP: Overtemperature fault propagation
1 = enabled
0 = disabled
OCP: Overcurrent fault propagation
1 = enabled
0 = disabled
UVP: Undervoltage fault propagation
1 = enabled
0 = disabled
OVP: Overvoltage error propagation
1 = enabled
0 = disabled
PVP: Phase voltage error propagation (Not Active)
1 = enabled
0 = disabled
R/W-0
PGM
Grouping of POLs
r g
R/W-1
ood message
TRP
One DPM can control up to 4
R/W-1
OTP
To enable fault propagation
R/W-1
OCP
2
A group of POLs is
C bus by writing into
R/W-1
UVP
R = R
W
U
- n
=
=
=
W
Unimplemented bit,
r
Value at POR reset
www.power-one.com
ead as ‘0’
eadable bit
ritable bit
R/W-1
OVP
R/W-1
PVP
Bit 0
8V to 14V Input
In this case low OK line will signal DPM to pull other
OK lines low to initiate shutdown of other POLs as
programmed in the GUI Fault and Error Propagation
window. If an error is propagated, the DPM can also
generate commands to turn off a front end (a DC-DC
converter generating the intermediate bus voltage)
and trigger an optional crowbar protection to
accelerate removal of the IBV voltage.
8.3.4.2
Propagation of a fault (OCP, UVP, OTP, and TRP)
initiates regular turn-off of other POLs. The faulty
POL in this case performs either the regular or the
fast turn-off depending on a specific fault as
described in section 8.3.2.
Propagation of an error initiates fast turn-off of other
POLs. The faulty POL performs the fast turn-off and
turns on its low side switch.
Example of the fault propagation is shown in Figure
35 - Figure 36. In this three-output system (refer to
the block diagram in Figure 16), the POL powering
the output V3 (Ch 1 in the picture) encounters the
undervoltage fault after the turn-on. When the fault
propagation is not enabled, the POL turns off and
generates the UV fault signal. Because the UV fault
triggers the regular turn off, the POL meets its turn-
off delay and falling slew rate settings during the
turn-ff process as shown in Figure 35. Since the UV
fault is programmed to be non-latching, the POL will
attempt to restart every 130ms, repeating the
process described above until the condition causing
the undervoltage is removed.
If the fault propagation between groups is enabled,
the POL powering the output V3 pulls its OK line low
and the DPM propagates the signal to the POL
powering the output V1 that belongs to other group.
ZY8105 5A DC-DC Intelligent POL
Figure 34. Fault and Error Propagation Window
Propagation Process
•
0.5V to 5.5V Output
Page 20 of 28
Data Sheet