CY325 ETC, CY325 Datasheet - Page 13
CY325
Manufacturer Part Number
CY325
Description
Stepper System Controller
Manufacturer
ETC
Datasheet
1.CY325.pdf
(107 pages)
- Current page: 13 of 107
- Download datasheet (2Mb)
DIP
9
10
-
11
DIP
12
DIP
13
DIP
14
DIP
15
© 2002 Cybernetic Micro Systems
PLCC
10
11
12
13
PLCC
14
PLCC
15
PLCC
16
PLCC
17
(I)
(I)
(O)
(O)
(O)
(I)
(I/O)
(I/O)
Pin Name
RESET
RxD
NC
TxD
These are TTL level serial data signals that can be used to issue
commands to or get replies from the CY545. Addition of an RS-232
voltage level driver/receiver, such as the Maxim MAX233, allows any RS-
232 device, such as the IBM PC COM1 port to talk directly to the CY545.
Pin Name
SW_SEL/
This signal is active when the CY545 is reading a parameter value from
external thumbwheel switches. The switch address is generated by the
parallel data bus.
Pin Name
IO_REQUEST/
This signal is driven low when a parallel command is issued to the
CY545. It is used as part of the parallel command handshake. If the
parallel command function is not used, this signal may select a fixed
serial baud rate as follows:
0 = 300 baud, 1 = 2400 baud, F = 9600 baud
Pin Name
XMEM_SEL/
This signal goes low when the CY545 reads or writes to the local external
memory. Data and addresses are generated by the parallel data bus. Up
to 64K bytes of external memory are supported. When this signal is
driven low at power-up or reset, the CY545 will not test for the Auto Start
key sequence or automatically execute commands from the external
memory.
Pin Name
BUSY/
BUSY/ is used with IO_REQUEST/ to implement the two line parallel
command handshake. This signal indicates that the CY545 has accepted
a parallel data character from the device driving the IO_REQUEST signal.
If the parallel handshake is not used, this pin may be tied low to select
fixed baud rates through the IO_REQUEST signal.
Description
CY545 hardware reset, active high pulse
Received serial data into CY545
No connection
Transmitted serial data from CY545
Description
Switch select
Description
Parallel handshake input signal
Description
External local memory select
Description
Parallel handshake acknowledgement
8
Chapter 2 - Pinout & Package Overview
www.ControlChips.com
Related parts for CY325
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
E-Series RF 1:1 Transformer 1710 - 1910 MHz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
LINEAR INTEGRATED CIRCUITS 3-TERMINAL VOLATGE REGULATORS
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
Simple function, 50 to 600W DC-DC converters
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
FC050S6R5POWER MODULES: DC-DC CONVERTERS; 18 TO 36 VDC INPUT, 6.5VDC OUTPUT; 50 W TO 150W
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
Disk OnChip 2000 DIP
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
512K x 16Bit x 2Banks Synchronous DRAM
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
5-Bit Shift Register Product Specfication
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
2N191alloy-junction germanium transistors
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
RTL8139DREALTEK SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
M11B416256A-25J256 K x 16 DRAM EDO PAGE MODE
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
IFR3000IFR3500 Rx IF/BASEBAND PROCESSOR
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
78M08LINEAR INTEGRATED CIRCUITS 3-TERMINAL VOLATGE REGULATORS
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
CS4231A-KLPARALLEL INTERFACE MULTIMEDIA AUDIO CODEC
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
CS4231A-KQPARALLEL INTERFACE MULTIMEDIA AUDIO CODEC
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
BC41B143A05-IRK-E4BlueCpre 4-ROM Single Chip Bluetooth v2.0 System with EDR
Manufacturer:
ETC ETC
Datasheet: