CY325 ETC, CY325 Datasheet - Page 50
CY325
Manufacturer Part Number
CY325
Description
Stepper System Controller
Manufacturer
ETC
Datasheet
1.CY325.pdf
(107 pages)
- Current page: 50 of 107
- Download datasheet (2Mb)
When the CY545 is reset, it will read the first three locations of the external memory. If the
values read are 12H, 34H, and 56H respectively, the CY545 will then switch to the program
execution mode, and start reading commands from location 00003 of the memory. This allows
the CY545 to work in a stand alone mode, without any commands from a host computer or
other source than the memory itself. This function is shown below:
This feature will only occur if the first three bytes have the proper key codes in them. Any other
values in those locations will keep the CY545 in the direct command mode, waiting for
commands from a host system before doing anything.
To set up the auto start function, simply record the data bytes 12h, 34h, and 56h, in locations 0
to 2 of the memory, followed immediately by the command sequence desired. For example:
When the CY545 is now reset, it will execute the memory-based commands, starting with the
“R125<cr>” command, since the key sequence was found in the first three locations.
As a special convenience, you may command the CY545 to ignore the auto start command
sequence, by holding the XMEM_SEL signal low while the CY545 is reset. If the signal is low,
the CY545 will not test the memory contents for the 12h, 34h, 56h key sequence. Instead, the
CY545 will set itself into the Command mode, and wait for commands from the serial or parallel
interface.
This is especially useful during program development, where errors in the memory content must
be corrected before the CY545 can run the memory based commands. Without this feature, you
would be forced to remove the memory and delete the key sequence, before the CY545 could
be operated with the memory again.
The sequence for bypassing the Auto Start tests is:
© 2002 Cybernetic Micro Systems
Y 0<cr>
E<cr>
<Ctrl-R>4V
R 125<cr>
F 15<cr>
.......
Q<cr>
•
•
•
•
•
Drive the XMEM_SEL signal low
Reset the CY545
Delay 2 milliseconds after reset is released
Release the XMEM_SEL signal
Issue any CY545 commands in the direct Command mode
00000
00001
00002
00003
Set memory pointer address to zero
Following sequence is recorded to memory
key sequence 12h, 34h, 56h
standard CY545 commands follow now
additional start up commands
End of memory content definition
12H
34H
56H
...
12H in address 0
34H in address 1
56H in address 2
First CY545 command in address 3
45
Chapter 12 - External Memory Support
www.ControlChips.com
Related parts for CY325
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
E-Series RF 1:1 Transformer 1710 - 1910 MHz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
LINEAR INTEGRATED CIRCUITS 3-TERMINAL VOLATGE REGULATORS
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
Simple function, 50 to 600W DC-DC converters
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
FC050S6R5POWER MODULES: DC-DC CONVERTERS; 18 TO 36 VDC INPUT, 6.5VDC OUTPUT; 50 W TO 150W
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
Disk OnChip 2000 DIP
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
512K x 16Bit x 2Banks Synchronous DRAM
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
5-Bit Shift Register Product Specfication
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
2N191alloy-junction germanium transistors
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
RTL8139DREALTEK SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
M11B416256A-25J256 K x 16 DRAM EDO PAGE MODE
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
IFR3000IFR3500 Rx IF/BASEBAND PROCESSOR
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
78M08LINEAR INTEGRATED CIRCUITS 3-TERMINAL VOLATGE REGULATORS
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
CS4231A-KLPARALLEL INTERFACE MULTIMEDIA AUDIO CODEC
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
CS4231A-KQPARALLEL INTERFACE MULTIMEDIA AUDIO CODEC
Manufacturer:
ETC ETC
Datasheet:
Part Number:
Description:
BC41B143A05-IRK-E4BlueCpre 4-ROM Single Chip Bluetooth v2.0 System with EDR
Manufacturer:
ETC ETC
Datasheet: