LPC2119 Philips Semiconductors (Acquired by NXP), LPC2119 Datasheet - Page 5

• Manufacturer Part Number: LPC2119
• Description: Single-chip 16/32-bit Microcontrollers; 128/256 KB Isp/iap Flash With 10-bit ADC And CANthe LPC2119/LPC2129 Are Based on a 16/32 Bit ARM7TDMI-STM Cpu With Real-time Emulation And Embedded Trace Support, Together With 128/256 Kilobytes (kB) of Embedde
• Manufacturer: Philips Semiconductors (Acquired by NXP)

Philips Semiconductors
Table 3:
9397 750 12806
Preliminary data
Symbol
P0.0 to P0.31
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
P0.8
P0.9
P0.10
P0.11
Pin description
Pin
19, 21, 22,
26, 27,
29-31, 33-35,
37-39, 41,
45-47, 53-55,
1-3, 5, 9, 11,
13-15
19
21
22
26
27
29
30
31
33
34
35
37
5.2 Pin description
Type
I/O
O
O
I
O
I
I/O
I
I/O
O
I
I/O
I
I/O
O
I/O
I
I
O
I
O
O
I
O
I
O
I
I
Description
Port 0: Port 0 is a 32-bit bi-directional I/O port with individual direction
controls for each bit. The operation of port 0 pins depends upon the pin
function selected via the Pin Connect Block. Pins 26 and 31 of port 0 are not
available.
TxD0 — Transmitter output for UART0.
PWM1 — Pulse Width Modulator output 1.
RxD0 — Receiver input for UART0.
PWM3 — Pulse Width Modulator output 3.
EINT0 — External interrupt 0 input
SCL — I
CAP0.0 — Capture input for Timer0, channel 0.
SDA — I
MAT0.0 — Match output for Timer0, channel 0.
EINT1 — External interrupt 1 input.
SCK0 — Serial clock for SPI0. SPI clock output from master or input to slave.
CAP0.1 — Capture input for Timer0, channel 1.
MISO0 — Master In Slave OUT for SPI0. Data input to SPI master or data
output from SPI slave.
MAT0.1 — Match output for Timer0, channel 1.
MOSI0 — Master Out Slave In for SPI0. Data output from SPI master or data
input to SPI slave.
CAP0.2 — Capture input for Timer0, channel 2.
SSEL0 — Slave Select for SPI0. Selects the SPI interface as a slave.
PWM2 — Pulse Width Modulator output 2.
EINT2 — External interrupt 2 input.
TxD1 — Transmitter output for UART1.
PWM4 — Pulse Width Modulator output 4.
RxD1 — Receiver input for UART1.
PWM6 — Pulse Width Modulator output 6.
EINT3 — External interrupt 3 input.
RTS1 — Request to Send output for UART1.
CAP1.0 — Capture input for Timer1, channel 0.
CTS1 — Clear to Send input for UART1.
Rev. 02 — 02 February 2004
2
2
C clock input/output. Open drain output (for I
C data input/output. Open drain output (for I
Single-chip 16/32-bit microcontrollers
LPC2119/LPC2129
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
2
2
C compliance).
C compliance).
5 of 36