LPC2119 Philips Semiconductors (Acquired by NXP), LPC2119 Datasheet - Page 6

• Manufacturer Part Number: LPC2119
• Description: Single-chip 16/32-bit Microcontrollers; 128/256 KB Isp/iap Flash With 10-bit ADC And CANthe LPC2119/LPC2129 Are Based on a 16/32 Bit ARM7TDMI-STM Cpu With Real-time Emulation And Embedded Trace Support, Together With 128/256 Kilobytes (kB) of Embedde
• Manufacturer: Philips Semiconductors (Acquired by NXP)

Philips Semiconductors
Table 3:
9397 750 12806
Preliminary data
Symbol
P0.12
P0.13
P0.14
P0.15
P0.16
P0.17
P0.18
P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
P0.27
Pin description
Pin
38
39
41
45
46
47
53
54
55
1
2
3
5
39
11
…continued
Type
I
I
O
O
O
I
I
I
I
I
O
I
I
I/O
O
I
I/O
O
O
I/O
I
O
I
I
O
I
I
O
I
O
O
I
I
O
Description
CAP1.1 — Capture input for Timer1, channel 1.
DSR1 — Data Set Ready input for UART1.
MAT1.0 — Match output for Timer1, channel 0.
DTR1 — Data Terminal Ready output for UART1.
MAT1.1 — Match output for Timer1, channel 1.
DCD1 — Data Carrier Detect input for UART1.
EINT1 — External interrupt 1 input.
Note: LOW on this pin while RESET is LOW forces on-chip boot-loader to
take control of the part after reset.
RI1 — Ring Indicator input for UART1.
EINT2 — External interrupt 2 input.
EINT0 — External interrupt 0 input.
MAT0.2 — Match output for Timer0, channel 2.
CAP0.2 — Capture input for Timer0, channel 2.
CAP1.2 — Capture input for Timer1, channel 2.
SCK1 — Serial Clock for SPI1. SPI clock output from master or input to slave.
MAT1.2 — Match output for Timer1, channel 2.
CAP1.3 — Capture input for Timer1, channel 3.
MISO1 — Master In Slave Out for SPI1. Data input to SPI master or data
output from SPI slave.
MAT1.3 — Match output for Timer1, channel 3.
MAT1.2 — Match output for Timer1, channel 2.
MOSI1 — Master Out Slave In for SPI1. Data output from SPI master or data
input to SPI slave.
CAP1.2 — Capture input for Timer1, channel 2.
MAT1.3 — Match output for Timer1, channel 3.
SSEL1 — Slave Select for SPI1. Selects the SPI interface as a slave.
EINT3 — External interrupt 3 input.
PWM5 — Pulse Width Modulator output 5.
CAP1.3 — Capture input for Timer1, channel 3.
CAP0.0 — Capture input for Timer0, channel 0.
MAT0.0 — Match output for Timer0, channel 0.
RD2 — CAN2 receiver input.
TD2 — CAN2 transmitter output.
RD1 — CAN1 receiver input.
AIN0 — A/D converter, input 0. This analog input is always connected to its
pin.
CAP0.1 — Capture input for Timer0, channel 1.
MAT0.1 — Match output for Timer0, channel 1.
Rev. 02 — 02 February 2004
Single-chip 16/32-bit microcontrollers
LPC2119/LPC2129
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
6 of 36